2
6
Hold 1 (Controller number 64)
Status
2nd byte 3rd byte
BnH 40H vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Control value:
00H - 7FH (0 - 127) 0-63 =
OFF, 64-127 = ON
*
Not received when the Receive Hold-1 parameter (SysEx) is OFF.
6
Portamento (Controller number 65)
Status
2nd byte 3rd byte
BnH 41H vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Control value:
00H - 7FH (0 - 127) 0-63 =
OFF, 64-127 = ON
*
The Part Portamento Switch parameter (PROG:PITCH) will change.
6
Resonance (Controller number 71)
Status
2nd byte 3rd byte
BnH 47H vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv= Resonance value (relative change): 00H - 40H - 7FH (-64 - 0 -
+63),
*
The Part Resonance Offset parameter (PROG:OFFSET) will change.
6
Release Time (Controller number 72)
Status
2nd byte 3rd byte
BnH 48H vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Release Time value (relative change): 00H - 40H - 7FH (-64 - 0 -
+63),
*
The Part Release Time Offset parameter (PROG:OFFSET) will change.
6
Attack time (Controller number 73)
Status
2nd byte 3rd byte
BnH 49H vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Attack time value (relative change): 00H - 40H - 7FH (-64 - 0 -
+63),
*
The Part Attack Time Offset parameter (PROG:OFFSET) will change.
6
Cutoff (Controller number 74)
Status
2nd byte 3rd byte
BnH 4AH vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Cutoff value (relative change):
00H - 40H - 7FH (-64 - 0 -
+63)
*
The Part Cutoff Offset parameter (PROG:OFFSET) will change.
6
Decay Time (Controller number 75)
Status
2nd byte 3rd byte
BnH 4BH vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Decay Time value (relative change): 00H - 40H - 7FH (-64 - 0 -
+63)
*
The Part Decay Time Offset parameter (PROG:OFFSET) will change.
6
Vibrato Rate (Controller number 76)
Status
2nd byte 3rd byte
BnH 4CH vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Vibrato Rate value (relative change): 00H - 40H - 7FH (-64 - 0 -
+63)
*
The Part Vibrato Rate parameter (PROG:OFFSET) will change.
6
Vibrato Depth (Controller number 77)
Status
2nd byte 3rd byte
BnH 4DH vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Vibrato Depth Value (relative change): 00H - 40H - 7FH (-64 - 0 -
+63)
*
The Part Vibrato Depth parameter (PROG:OFFSET) will change.
6
Vibrato Delay (Controller number 78)
Status
2nd byte 3rd byte
BnH 4EH vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Vibrato Delay value (relative change): 00H - 40H - 7FH (-64 - 0 -
+63)
*
The Part Vibrato Delay parameter (PROG:OFFSET) will change.
6
General Purpose Effect 1 (Reverb Send Level)
(Controller number 91)
Status
2nd byte 3rd byte
BnH 5BH vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Reverb Send Level:
00H - 7FH (0 - 127)
*
The Part Reverb Send Level parameter (PROG:MAIN) will change.
6
General Purpose Effect 4 (Delay Send Level)
(Controller number 94)
Status
2nd byte 3rd byte
BnH 5EH vvH
n = MIDI channel number:
0H - FH (ch.1 - 16)
vv = Delay Send Level:
00H - 7FH (0 - 127)
*
The Part Delay Send Level parameter (PROG:MAIN) will change.
6
NRPN MSB/LSB (Controller number 98, 99)
Status
2nd byte 3rd byte
BnH 63H mmH
BnH 62H llH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by NRPN
ll = lower byte (LSB) of parameter number specified by NRPN
<<< NRPN >>>
The NRPN (Non Registerd Parameter Number) message allows an extended
range of control changes to be used. On this unit, NRPN messages can
be used to modify sound parameters etc.
To use these messages, you must first use NRPN messages (Controller
number 98 and 99, their order does not matter) to specify the
parameter to be controlled, and then use Data Entry messages to
specify the value of the specified parameter. Once an NRPN parameters
has been specified, all Data Entry messages received on that channel
will modify the value of that parameter. To prevent accidents, it is
recomended that you set RPN Null (RPN Number = 7FH/7FH) when you have
finished setting the value of the desired parameter.
*
For more about the NRPN that JD-Xi receive, refer to Control Change
