10
Utilisation d'un commutateur au pied
à verrouillage
Les amplificateurs CUBE-40XL et CUBE-80XL prennent également en
charge les commutateurs au pied à verrouillage. Si vous utilisez un
commutateur au pied à verrouillage, effectuez les réglages suivants.
Réglage FOOT SW TYPE
Il existe deux types de commutateurs au pied.
Type
Fonctionnement
À effet momentané
(BOSS FS-5U, etc.)
Ce type de commutateur au pied s'active (ou se
désactive) lorsqu'il est enfoncé et se désactive
(ou s'active) lorsqu'il est relâché.
À verrouillage
(BOSS FS-5L, etc.)
Ce type de commutateur au pied s'active ou se
désactive chaque fois qu'il est enfoncé.
*
Le commutateur BOSS FS-6 peut fonctionner comme commutateur
au pied à effet momentané ou à verrouillage.
CUBE-40XL
À la sortie d'usine, le type à effet momentané est sélectionné. Vous
pouvez modifier ce réglage comme suit.
•
Pour spécifier le type à verrouillage
Mettez l'appareil sous tension tout en maintenant le bouton
[TAP/STOP] enfoncé.
•
Pour spécifier le type à effet momentané
Mettez l'appareil sous tension tout en maintenant le bouton
[REC/PLAY/DUB] enfoncé.
CUBE-80XL
Réglez le commutateur [FOOT SW TYPE] situé sur
le panneau arrière de l’appareil en position FS-5L
(LATCH).
*
Ce réglage est mémorisé même après la mise
hors tension.
Réglages du commutateur au pied
(BAGUE)
(POINTE)
Commutateur de
polarité
BOSS FS-5L
REVERB
SOLO
EFX
CH SELECT
EFX
CH SELECT
REVERB
SOLO
B
A
Réglez les commutateurs comme indiqué
ci-dessous.
BOSS FS-6
(BAGUE)
(POINTE)
Commutateur de
polarité
BOSS FS-5L+FS-5U
DELAY/
REC/PLAY/DUB
TAP/STOP
DELAY/
REC/PLAY/DUB
TAP/STOP
B
A
Réglez les commutateurs comme indiqué
ci-dessous.
BOSS FS-6
*
Même si le commutateur FOOT SW TYPE est réglé sur FS-5L (LATCH),
vous devez toujours utiliser un commutateur au pied à effet
momentané pour TAP/STOP. Cela ne fonctionne pas correctement
avec un commutateur au pied à verrouillage.
Remarques importantes concernant l'utilisation d'un
commutateur au pied à verrouillage
Les réglages on/off du commutateur au pied prévalent sur ceux du
panneau de contrôle pour activer et désactiver les effets EFX, DELAY
ou REVERB.
Toutefois, les réglages on/off des effets EFX, DELAY ou REVERB, stockés
en mémoire à l'aide de la fonction SOLO, prévalent lorsqu'ils sont
invoqués avec cette dernière. Cela peut produire un conflit d'affichage
entre les témoins du panneau de contrôle et du commutateur au pied,
mais il ne s'agit pas d'un dysfonctionnement.
Applications pratiques
Vous pouvez utiliser les réglages suivants pour contrôler les opérations
lorsque les réglages effectués sur le panneau de contrôle pour les
effets EFX, DELAY et REVERB sont invoqués à l'aide de la fonction SOLO.
Mode prioritaire du commutateur au pied
Donnez toujours la priorité au réglage on/off du commutateur au pied.
Pour effectuer le réglage :
Maintenez le commutateur [SELECT] enfoncé et mettez l'appareil sous
tension.
Mode prioritaire en mémoire (réglage en usine)
Donnez toujours la priorité au réglage on/off enregistré à l'aide de la
fonction SOLO.
Pour effectuer le réglage :
Maintenez le commutateur [TUNER] enfoncé et mettez l'appareil sous
tension.
*
Le réglage modifié reste en mémoire lorsque l'appareil est mis hors
tension.
Summary of Contents for CUBE 40XL
