AD-3
Dec. 1998
5
AD-3 Test mode and version checking procedure
◆
Test items
1. PEDAL switch, POWER LED, SELECT switch check
2. DSP, DRAM, CPU check
3. Version check
4. Volume check (except for INPUT LEVEL)
5. Output frequency response check
6. Residual noise, shock noise check (DSP thru)
7. Overall circuit frequency response check
8. SELECT Switch check
9. Output mute check
10. Maximum output level check
11. Peak LED, Input Level volume check
12. Battery operation check
13. Input switch check
◆
Required items
• Stereo-mono (L/R) cable: PCS-31 (or equivalent)
• Mono phone cable
×
2
• Multiple jack: J-5 (or equivalent)
• Short plug
• Oscillator
• Oscilloscope
• Noise meter
• Monitor speaker
• PSA adaptor (or 9V DC power supply)
◆
Notes
Make the following settings before you perform the tests.
1. Connect the output of the AD-3 to the stereo plug end of the PCS-31.
See figure1.
2. Measurements are to be made between the white (HOT: TIP) and red
(COLD: RING).
Check both Lch and Rch.
Check the phase inversion between Hot and Cold so output signal is
Balance Output. See figure3.
◆
Entering test mode
• First set the INPUT LEVEL to maximum, and all other knobs to
minimum.
• While pressing the ANTI-FEEDBACK AUTO (subsequently
referred to as AFB) and CHORUS (subsequently referred to as CHO)
pedals, turn on the power, and immediately move the SELECT
switch.
* Note: If you release the AFB or CHO pedals, test mode will be
defeated. Be sure to press them firmly.
Because of the internal oscillator function, it has been made
intentionally difficult to enter test mode.
• When you move the SELECT switch, the following operations will
occur.
●
AFB, CHO and PEAK LEDs will blink simultaneously -> LEDs will
light in the order of AFB, CHO, and PEAK -> AFB, CHO, and
PEAK LEDs will blink simultaneously, and will stop with the AFB
LED lit.
The above includes verification of test items 1--3.
1. PEDAL switch, POWER LED, SELECT switch check
• When test mode is entered, these switches are verified.
• If even one of these switches does not function, it will not be possible
to enter test mode.
• When you check these switches, the AFB, CHO, and PEAK LEDs
will blink.
* Note: Be sure to press the pedal switch all the way.
• Verify that the POWER LED lights.
2. DSP, DRAM, CPU check
• Immediately after test 1, the LEDs will light in the order of AFB,
CHO, and PEAK.
• If an error occurs, an LED will halt in a blinking state.
• The location of the blinking LED will indicate the content of the error.
Refer to table 1.
• After all three LEDs blink, the test will proceed to the next step.
3. In order to check battery operation, insert batteries. (Included: six AA
alkaline batteries)
4. Connect the PSA-Series.
3. Version check
• After test 2, verify that the AFB LED is lit.
• This indicates version 1.00.
• For the remainder of the version number, refer to table 2.
Fig. 1
Table .1
Table .2
AFB LED
CHO LED
PEAK LED
Error Message
DSP busy Error
DSP P/IRAM
Error
DSP ERAM Error
VERSION
AFB LED
CHORUS LED
PEAK LED
1.00
1.01
1.02
1.03
: Light
: Dark
: Light
: Dark
テストモード、バージョンの確認方法
◆テスト項目
1.
PEDALスイッチ、POWER LED、SELECTスイッチ チェック
2. DSP
、DRAM、CPUチェック
3. VERSION
確認
4.
ボリュームチェック(INPUT LEVELを除く)
5.
出力f特チェック
6.
残留ノイズ、ショックノイズ チェック(DSPスルー)
7.
回路全体の f 特チェック
8. SELECTスイッチ チェック
9. 出力ミュート チェック
10.
最大出力レベル チェック
11. PEAK LED
、INPUT LEVELボリューム チェック
12.
電池動作チェック
13. INPUT
スイッチ チェック
◆用意する機材
・ ステレオ−モノラル(L/R)コード:PCS-31(または相当品)
・ モノラル標準コード×2
・マルチプルジャック:J-5(または相当品)
・ショートプラグ
・発振器
・オシロスコープ
・ ノイズメーター
・ モニタースピーカー
・ PSAアダプター(またはDC電源9V)
◆注意:
テストを行う前に、下記の設定をしておいてください。
1. AD-3の出力はPCS-31のステレオ・プラグ側を接続。図1参照
2. 測定はPCS-31の白色(HOT:TIP側)、赤色(COLD:RING側)を
測定する。
L/R共確認する事。
出力はバランス出力なので、HOTとCOLDで位相が反転してい
る事を確認する。
図3参照
◆テスト・モードへの入り方
・まずINPUT LEVELは最大、他の全ツマミを最小にします。
・ANTI-FEEDBACK AUTO(以後AFB)、CHORUS(以後
CHO)のPEDALを 押しながら電源を入れ、直ちに、SELECT
スイッチを切り替えます。
*注意:AFB、CHOのPEDALを放すと、解除されるので確実に
押すこと。
内部発振機能があるため、容易にテスト・モードに入れないよ
うになっています。
・SELECTスイッチを切り替えると同時に下記の一連の動作をし
ます。
●AFB、CHO、PEAKのLEDが同時に点滅 → AFB、CHO、
PEAKの順にLED点灯 →
AFB
、CHO、PEAKのLEDが同時に点
滅し、AFB LED点灯で止まる。
上記はテスト項目1〜3までの確認を含んでいます。
1. PEDALスイッチ、POWER LED、SELECTスイッチ チェック
・テスト・モードに入る時、これらのスイッチの確認をしていま
す。
・一つでも動作しない場合は、テストモードには入りません。
・これらのスイッチを確認するとAFB、CHO、PEAKのLEDが点
滅します。
*注意:ペダル・スイッチは確実に押して下さい。
・POWER LEDの点灯を確認してください。
2. DSP、DRAM、CPUチェック
・1.の後、直ちにAFB、CHO、PEAKの順にLEDが点灯して行
きます。
・ エラーがあった場合、LEDは点滅停止します。
・ LEDの点滅位置でエラーの内容を表します。表1参照。
・3つのLEDが全点滅した後、次のステップに移動しています。
3. 電池動作確認のため、電池を入れておく。(付属品:アルカリ
単三電池6本)
4. PSA-100アダプター接続。
3. VERSION確認
・2.の試験後、AFB LEDが点灯しているのを確認する。
・これはVERSION 1.00を表示しています。
・他のバージョンは表2を参照してください。
/図1
/表1
/表2
/ 点灯
/ 消灯
/ 点灯
/ 消灯