manualshive.com logo in svg

Roksan Audio Xerxes.20plus, User Manual

Share
Download
Roksan Audio Xerxes.20plus User Manual Download Page 18

Roksan Audio ltd

  

Xerxes.20

plus

 Record Player User Manual 

 

 

General Use 

 

 

Version 2.00 

All specifications are liable to change without notice. E&OE

 

Page 18 of 22

 

ENGLISH

 

•

  Clean the belt with a non-alcohol wax based polish. It is advisable to change the belt after every five 

years or after five thousand hours of use. 

 

•

  Clean the dust cover with a damp cloth as and when required. 

 

•

  The turntable is made of very high quality real wood veneer (or high gloss lacquer) and should be looked 

after with care. It may be cleaned with a very soft cloth. For any stubborn marks, use a very slightly 
moistened lint free cloth. Very little high quality furniture wood polish may be used every six to eight 
months. DO NOT USE CLEANING AGENTS, SOLVENT OR ABRASIVES. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Refer to SETUP section above for detail on charging the Main Bearing with Roksan Supplied oil. 

 

5

Bearing Ball 

Impression 

4

 

No Bearing Ball 

Impression 

Summary of Contents for Xerxes.20plus























Reviews:

No comments

Brands by name

Popular brands

Load more brands