background image

 

16/23

 

User’s  Guide 

HB2637L-EVK-301 

© 2022 ROHM Co., Ltd.

 

No. 65UG002E Rev.001

 

Apr.  2022

 

To characterize the low side device, a jumper must be placed between HS_PWM and GND of the connector CO2. Provide the 

necessary pulse on the LS_PWM pin of connector CO2 or at the BNC connector provided on the board. Choose the appropriate 

inductor and the pulse width such that the required drain current for the test is achieved. On the board a 5uF bulk capacitor is 

already provided, however depending on the test current level, an external bulk capacitor will be required to minimize the DC 

link voltage drop.     

Set the required HVDC voltage and do not exceed above 900V. For performing the double pulse measurements a heatsink is 

not required. 

 

Other topologies such as buck, boost, synchronous buck/boost, 2-level inverter are also possible. For such topologies depend-

ing on output power a heatsink might be required. Figures 14, 15 and 16 show the setup and connection required for a synchro-

nous buck, synchronous boost and 2-level inverter respectively.   

 

 

Figure 14: Synchronous Buck Converter test set up 

 

Figure 15: Synchronous Boost Converter test set up 

Summary of Contents for TO-263-7L

























Reviews: