Rohde & Schwarz CMW-B400B User Manual Download

Page: 60 / 97

Command Reference

R&S

CMW-B400B/-B405A

User Manual 1176.8116.02 ─ 04

FETCh:AUDio:MEAS:ANALog:STATe:ALL?
FETCh:AUDio:MEAS:DIGital:STATe:ALL?

Queries the main measurement state and the measurement substates. Both measure-
ment substates are relevant for running measurements only. Use

FETCh:...:STATe?

to query the main measurement state only. Use

INITiate...,

STOP..., ABORt...

to change the measurement state.

See also: "Measurement Control" in the R&S

CMW user manual, chapter "Remote

Control"

Return values:

OFF | RDY | RUN

OFF:

measurement switched off, no resources allocated, no

results available (when entered after

STOP...

)

RDY:

measurement has been terminated, valid results may be

available

RUN:

measurement running (after

INITiate..., READ...

synchronization pending or adjusted, resources active or queued
*RST:

OFF

PEND | ADJ | INV

PEND:

waiting for resource allocation, adjustment, hardware

switching ("pending")

ADJ:

all necessary adjustments finished, measurement running

("adjusted")

INV:

not applicable because <MainState>: OFF or RDY ("inva-

lid")

QUE | ACT | INV

QUE:

measurement without resources, no results available

("queued")

ACT:

resources allocated, acquisition of results in progress but

not complete ("active")

INV:

not applicable because <MainState>: OFF or RDY ("inva-

lid")

Usage:

Query only

Firmware/Software:

V3.2.10

Manual operation:

See

"Digital Meas (Softkey)"

on page 29

6.3.2 General Measurement Settings

The following commands configure measurement settings applicable to all signal
types.

CONFigure:AUDio:MEAS:ANALog:RTYPe?

...................................................................61

CONFigure:AUDio:MEAS:DIGital:RTYPe?

..................................................................... 61

CONFigure:AUDio:MEAS:ANALog:REPetition

................................................................61

CONFigure:AUDio:MEAS:DIGital:REPetition

.................................................................. 61

Audio Measurements

深圳德标仪器

135-1095-0799

Summary of Contents for CMW-B400B


































































































Search results

Summary of Contents for CMW-B400B

Reviews:

Related manuals for CMW-B400B

Brands by name

Popular brands

Rohde & Schwarz CMW-B400B, User Manual

Search results

Summary of Contents for CMW-B400B

Reviews:

Related manuals for CMW-B400B

Brands by name

Popular brands