Rohde & Schwarz CMW-B400B User Manual Download

Page: 43 / 97

GUI Reference

R&S

CMW-B400B/-B405A

User Manual 1176.8116.02 ─ 04

List Section

Specifies the start and stop index of the tone list and thus also the number of tones in
the list "Count".

To apply changes, press the Apply button. When the dialog is closed, changes are
applied automatically.

Remote command:

SOURce:AUDio:GEN:ANALog:MULTitone:STARt
SOURce:AUDio:GEN:ANALog:MULTitone:STOP
SOURce:AUDio:GEN:DIGital:MULTitone:STARt
SOURce:AUDio:GEN:DIGital:MULTitone:STOP

List

The first column specifies the frequency of each tone. The second column displays or
specifies the level of each tone, depending on the configured "Level Handling".

All entries must have different frequencies.

Remote command:

SOURce:AUDio:GEN:ANALog:MULTitone:TONE<no>:TDEFinition
SOURce:AUDio:GEN:ANALog:MULTitone:TDEFinition
SOURce:AUDio:GEN:DIGital:MULTitone:TONE<no>:TDEFinition
SOURce:AUDio:GEN:DIGital:MULTitone:TDEFinition

Tone List (Hotkey)

If the signal type is set to "Multitone", the generator hotkey "Tone List" is available.

The hotkey opens the following dialog box:

The dialog box provides the list settings described above (see "List", "Level Handling"
and "List Section").

Additionally, the box allows to fill the "Frequency" column of the tone list by selecting a
start frequency and an increment.

Audio Generator Settings

深圳德标仪器

135-1095-0799

Summary of Contents for CMW-B400B


































































































Search results

Summary of Contents for CMW-B400B

Reviews:

Related manuals for CMW-B400B

Brands by name

Popular brands

Rohde & Schwarz CMW-B400B, User Manual

Search results

Summary of Contents for CMW-B400B

Reviews:

Related manuals for CMW-B400B

Brands by name

Popular brands