Roger SL2000H Manual Download Page 6

Security Lock SL2000H v1.0 EN Rev.C.doc   

2011-11-16 

 

 

 

Page 6 of 11

 

 
 

[*][Old INSTALLER Code][#][New INSTALLER Code] [#] 

This command erases the current INSTALLER code and program a new one. If command 
is successfully accomplished the unit generates three series of two beeps (** ** **) 

[*] [Old MASTER Code] [#][Old MASTER Code] [#] 

This command erases the current MASTER code and program a new one. If command is 
successfully accomplished the unit generates three series of two beeps (** ** **). 

[#]  

Normally pressing [#] is used to mark the end of the code but when pressed separately 
for a time longer the 0.5s it triggers Door Bell indication. 

Programming The USER Codes 

The SL2000 enables programming of up to 55 different USER codes. The USER codes can 
be managed (added/deleted/changed) only in the Installer Programming mode (to enter 
Installer Programming mode press: [INSTALLER Code]+[#]). Once in the Installer 
Programming mode you have following commands: 

[0] [1] [#] [code] [# ]

   ; Programming of the USER code no. 1 

[0] [2] [#] [code] [#]

 

; Programming of the USER code no. 2 

… etc. 
… etc. 
… etc. 

[5] [5] [#] [code] [#]

 

; Programming of the USER code no. 55 

[0] [0] [#]

   

 

; Delete all USER codes 

[9] [9] [#][code][#]

 

; Deletes the code entered in square brackets 

[#]

 

 

 

 

; Exit from the Installer Programming mode 

When the SL2000 accepts the new USER code it generates two series of two beeps (** 
**). Any attempt to program the USER code which already exists in the memory or to 
program it with a wrong length then will cause the programming error signaled by a long 
acoustic beep.  

Configuring the SL2000 — Memory Reset 

In order to configure the SL2000 you must perform the Memory Reset procedure and 
then enroll sequentially 10 digits (C1,C2..C10) which will configure the unit for the 
individual installation. After the Memory Reset the entire code lock memory is erased 
(including all codes) and initialized with default (factory)

 

settings.  

In order to perform Memory Reset do the following steps: 

 

Turn off the power supply 

 

Put the jumper on JP1 contacts 

 

Turn on the power supply 

 

Wait till the moment when SL2000 will generate three series of two beeps (**  **  
**) - this signal indicates that unit has erased memory and restored default 
configuration parameters 

 

Remove jumper from JP1 contacts 

Meaning of the configuration parameters: C1-C10 
C1C2:

 Specifies the time delay from a moment when USER code is entered till moment 

when Door Lock output will be triggered. It can be programmed from 00 to 99s (default: 
04). 

Note: Whenever you re-program MASTER or INSTALLER code remember that new code 

programmed into a unit must have the same length as the old one. 

Summary of Contents for SL2000H












Reviews: