background image

S TO R AG E   &   C A R E

- 18 -

When not in use, always keep your PinMic™ in the storage 
case provided. Close and snap the storage case for 
complete protection. 

Inside the case, you will fi nd a sachet of moisture absorbent 
crystals. Please retain these crystals and store with the 
PinMic™ to keep the microphone in ideal condition.

Eventually this pack of crystals will need to be dried. This 
is indicated by the crystals turning pink in colour. They can 
easily be re-used by placing them in an oven at 100-150 
degrees Celsius for approximately ten minutes. The crystals 
will operate effectively again once they have turned blue.

In some cases, such as when there are multiple users of the 
PinMic™, you may wish to sanitise the backplate and cable.

To do this, use the provided Sanitary Cleansing Wipes to 
wipe down the PinMic™ surface. You may wish to detach the 
microphone from the backplate and cable for easier access.

Please be mindful when cleaning the PinMic™ not to let any 
dust or moisture into the microphone capsule.

122-950-1-3_PinMic_manual_newspec.indd   18

122-950-1-3_PinMic_manual_newspec.indd   18

1/27/2011   3:14:25 PM

1/27/2011   3:14:25 PM

Summary of Contents for Pinmic





















Reviews: