Decoder interface
1
3
5
7
9
13
15
17
19
21
2
4
6
8
10
12
14
16
18
20
22
P
lux
16
GB
Starting locomotive operation
Maintenance of the model
high beam, Drivers cab 1 Aux. 6
Aux. 7
GPIO/C
Zugbus-Clock / GPIO/B
Masse GND
Front light, Drivers cab 1
V (+)
Twist protection
Front light, Drivers cab 2
Speaker A
Speaker B
Aux. 4
Aux. 3
GPIO/A / Zugbus-Data
DC (+) Elko
Engine right (+)
Engine left (-)
Track right / Pick up
Track left / Tracks
Aux. 1 red Taillight, Drivers cab 2
Aux. 2 red Taillight, Drivers cab 1
Aux. 5 high beam, Drivers cab 2
Unwrap model:
Take out the model cautiously
UGRFÏDMGJÏÍEÏ
Operating instructions:
Before use is advisab-
le to let the loco go around about 30 minutes for-
wards an 30 minutes backwards without load, to
obtain an optomal circuit and best tractive power.
The smallest radius this model should run is
R2
of
the ROCO track system (R2 = 358 mm).
Your locomotive will run smoothly on clean tracks
only. For this purpose we recommend using item
no.
46400, Roco track cleaning van
, or item
no.
10002, Roco track cleaning rubber
, for
removing heavy dirt.
Fittings:
Operation is possible with different
AMSNJGLEQÏÍEÏÏ5CÏPCAMKKCLBÏSQGLEÏRFCÏ0MAMÏ
close coupling.In the enclosed accessory bag you
UGJJÏÍLBÏQK?JJÏIGRQÏRMÏ@CÏÍRRCBÏMLÏWMSPÏJMAMKMRGTCÏ
Please
mount them cautiously.
Attention!
3QCÏEJSCÏMLJWÏGDÏGLBGA?RCBÏÍEÏÏ
Running in digital mode:
Remove the jumper from the interface.
Finally put the plug of the chip into the interface
?QÏQFMULÏGLÏÍEÏ
A.C. operation:
ÏQCCÏÍEÏ
To enjoy your model for a long time, it is necesary
to
service
it regulary (i.e. after it has been in ope-
ration for approximately 30 hours).
1. Cleaning of wheel contacts:
Wheel cont-
acts easily get dirty on tracks which are not enti-
rely clean. Use a small brush to
remove dirt
from
QNMRQÏK?PICBÏGLÏÍEÏ
2. Lubrication:
Apply
tiny oil drops
to spots
K?PICBÏGLÏÍEÏÏ.PGMPÏRMÏJS@PGA?RGMLÏBGQK?LRJCÏJM
-
AMKMRGTCÏÍEÏÏ5CÏPCAMKKCLBÏSQGLEÏGRCKÏLMÏ
10906, Roco oiler
. For lubrication the gearparts
(e.g. cogwheels, worm) we whould recommended
our Roco
special grease
(item no.
10905
).
Attention:
Please do not oil these parts when
using our grease.
3. Change of traction tyre:
Remove the gear
AMTCPÏ ÍEÏ Ï2?ICÏ MSRÏ
wheel set
and remove
traction tyre
ÏSQGLEÏ?ÏNGLÏMPÏ?ÏÍLCÏQAPCUBPGTCPÏ
ÍEÏ Ï5FCLÏ NPCQQGLEÏ MLÏ RFCÏ LCUÏ RP?ARGMLÏ RWPCÏ
please
avoid twisting it
.
4. Carbon Brush Changing:
First remove loco
@MBWÏÍEÏÏ?LBÏRFCLÏRFCÏKMRMPÏÍEÏ
Assembly:
During assembly please take care of
correct position of contacts.
10
3
