background image

To order parts and supplies: 800.343.9353  >>  eastwood.com 

3

 

 READ INSTRUCTIONS 

•  Thoroughly read and understand these product instructions before using 

this tool. Failure to follow all warnings can result in tool damage or serious 
physical injury.

•  Keep these product instructions for future reference.

 

EYE INJURY HAZARD!

•  Rapidly rotating surfaces can eject metal particles, dirt and debris at high 

velocity. Always wear ANSI approved eye protection when operating this 
tool.

 

HEARING DAMAGE HAZARD!

•  This Rockwood Pneumatic Tool emits high sound levels while operating.  

Use ANSI approved ear protection when operating. 

 

BURSTING HAZARD!

•  Do not exceed 90 psi (6.2 bar) of tool inlet pressure. Permanent tool  

damage and/or bursting could occur and cause personal injury.

 

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

 

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

 

CAUTION used with the safety alert symbol, indicates a hazardous situation which, if not avoided, 
could result in minor or moderate injury.

 

NOTICE is used to address practices not related to personal injury.

SAFETY INFORMATION

The following explanations are displayed in this manual, on the labeling, and on all other information 
provided with this product:

Summary of Contents for 31538









Reviews: