HigH PReSSuRe WaSHeR
eN
8
3) Before operate high pressure washer, press the
trigger switch (15) to bleed any trapped air out of
the pump and hose. (See Fig. K)
4) Start the pressure washer by turning ON/OFF
switch to ON. Press the trigger. Reminder: motor
does not run continuously, only when trigger is
squeezed. (See Fig. L)
2.SuRFaCe PRePaRaTiON
Before staring any cleaning task it is important the
area for objects which could create a hazard. Remove
objects from the work area which area which could
be tripped over, such as toys or outdoor furniture.
Ensure that all doors and windows are closed tight.
3. uSiNg THe aCCeSSORieS
1) adjuSTabLe WaNd
The adjustable nozzle allows you to use any variety of
spray patterns from a fan spray to a pencil jet spray.
When using pressure washer to clean wood decks,
siding, vehicles etc., always start using the fan spray
and begin spraying from a minimum 36” away to avoid
damaging the surface of the material you are cleaning.
CauTiON:
Do not adjust the nozzle while the
trigger is squeezed.
2) adjuSTiNg THe SPRaY
The adjustable spray nozzle can adjust from fan to
jet setting. The spray is adjusted from jet spray to fan
spray by turning the nozzle. (See Fig. M).
NOTe:
The pressure of the spray on the surface you
are cleaning increases as you move the wand closer
to the surface.
CauTiON:
Jet spray adjustment is very
aggressive. Do not adjust while spraying.
We recommend that for most cleaning applications
a 20-degree spray angle should be used to avoid
damage to the surface being sprayed.
STORage
The machine should be stored in a frost-free room!
Pump, hose and accessories should always be emp-
tied of water prior to storing as follows:
Stop the machine and detach water hose and acces-
sory.
Restart the machine and activate the trigger. Let the
machine run until no more water runs through the
spray gun.
3. Stop the machine, unplug and wind up hose and
cable.
4. Place spray handle, nozzles and other accessories
in the holders of the machine. Should the machine by
mistake be frozen, it will be necessary to check it for
damage.
NeVeR STaRT-uP a FROzeN MaCHiNe.
Frost damages are not covered by the guarantee!
Winding up of electric cable and high pressure
hose
To avoid accidents, the electric cable and the high
pressure hose should always be winded carefully up
around the handle. Wind up the cable on the appropri-
ate hook.
Storage of accessories
The lance and the nozzles can be stored on the pres-
sure washer.
MaiNTeNaNCe
WaRNiNg!
Always disconnect the electrical
plug from the socket prior to maintenance or
cleaning. To ensure a long and problem free working
life, please take the following advice:
- Wash out water hose, high pressure hose, spray
lance and accessories before mounting.
- Clean the connectors of dust and sand.
- Rinse the detergent spraying attachment after
use.
- Clean the nozzles.
Any repair should always be made in an authorized
workshop with original spare parts.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
CLeaNiNg OF WaTeR iNLeT FiLTeR
Clean the water inlet filter regularly once a month or
more frequently according to use.
Unscrew quick connector and take water inlet out.
Check that it is intact before re-mounting it.
The inlet filter must always be fitted inside the water
inlet pipe to filter out sand, limestone and other impu-
rities, as they will damage the pump valves.
CauTiON:
Failure to fit the filter will invalidate
the guarantee.
Cleaning of nozzle
A clogging up in the nozzle causes a pump pressure
