7
HigH PReSSuRe WaSHeR
eN
TeCHNiCaL daTa
Rated voltage
220-240V ~ 50Hz
Rated input power
1400W
Rated working pressure
7MPa (1015PSI)
Max. permissible pressure
10MPa (1450PSI)
Rated flow rate
5.5 l/min
Max. flow rate
6.5 l/min
Max. inlet water pressure
0.7MPa
Degree of protection
IPX5
Rated temperature
0-40
o
C
Insulation class
/II
Machine weight
5.3kg
OPeRaTiNg iNSTRuCTiONS
NOTe:
Before using the tool, read the
instruction book carefully.
CauTiON!
• Never use the pressure washer to draw in water
contaminated with solvents (e.g. paint thinners,
gasoline, oil, etc.).
• Dirt in the feed water will damage the unit. To
avoid this risk, we recommended checking the
water filter (located inside the water inlet; to clean
it out see maintenance section).
• Always prevent debris from being drawn into the
unit by using a clean water source and an acces-
sory water source and an accessory water filter if
required.
Water supply (cold water only)
1. Do not draw non-water liquids through the unit.
For use with cold water supply only.
2. Water hose must be at least a 1/2” in diameter.
3. Flow rate of water supply must not fall below 6 l /
min.
4. Flow rate can be determined by running the water
for one minute into an empty container.
5. The water supply temperature must not exceed
40
o
C (104
o
F)
aSSeMbLY
1. aSSeMbLiNg SPRaY guN HOLdeR
Press the spray gun holder (9) on to the machine.
(See Fig, A)
2. MOuNTiNg OF HOLdeR FOR eLeCTRiC CabLe
Press the holder for electric cable (4) on to the
machine. (See Fig. B)
3. MOuNTiNg OF WHeeLS
Mount the wheels (12) by pressing them into the
bracket. (See Fig. C1)
4. MOuNTiNg OF iNLeT WaTeR CONNeCTOR
Unscrew white protection cap from inlet thread, screw
quick connector to inlet (13). Please ensure water filter
always fitted before every operation.(See Fig.C2)
5. MOuNTiNg OF adjuSTabLe SPRaY NOzzLe aNd
LaNCe HOLdeR
Place the lance holder fence (10) on to the machine,
and fix the screws. (See Fig. D)
6. MOuNTiNg OF HaNdLe
Press the handle (14) on to the machine, and fix the
screws. (See Fig. E)
7. aSSeMbLiNg THe HigH PReSSuRe HOSe
1) Make sure that ON/OFF switch is in OFF position.
(See Fig. F)
2) Insert the high-pressure hose to spray gun.
(See Fig. G)
3) Insert the connection lance (16) into spray gun,
and twist 1/4turn. Then insert the adjustable spray
lance (8) into the connection lance (16), and twist
1/4turn until rectangular tab appears. (See Fig. H)
4) Unscrew white protection cap from outlet thread
and connect high pressure hose with outlet (2),
and then tighten ring (a) with clockwise. (See Fig.I)
8. CONNeCTiNg WaTeR SuPPLY
Connect water pipe with female coupler (no supplied)
to quick connector of inlet.(See Fig. J)
OPeRaTiON
1. ON/OFF SaFeTY SWiTCH
1) Connect the plug to into a properly outlet.
2) Trigger switch is in a locked off position to prevent
in accidental starting. Depress safety lock (5) to
“unlocking” position, then trigger switch is now
on. Release trigger switch (15) and depress safety
lock (5) to “locking” position to activate safety
lock.(See Fig. K)
