11
CoRDLESS DRILL
EN
pack is now fully charged, unplug the charger and
remove the battery pack.
wARNING: when battery charge runs out
after continuously use or exposure to direct
sunlight or heat, allow time for the tool to cool down
before re-charging to achieve the full charge.
CHARGING INDICAToR
This charger is designed to detect some problems
that can arise with battery packs. Indicator lights
indicate problems (see table below). If this occurs,
insert a new battery pack to determine if the charger
is OK. If the new battery charges correctly, then the
original pack is defective and should be returned to
a service center or recycling service center. If the
new battery pack displays the same problem as the
original Battery Pack, have the charger tested at an
authorized service center.
Light
oN/oFF Flash
Status
Green on
Red flash
Charging
Red flash
Green flash
Defective Battery
Green on
Red on
Fully Charged
Green Off
Red flash
Hot/Cold Delay
2. REMovE oR INSTALL BATTERy PACk (See Fig. B1, B2)
Press both of the Battery Pack Release Buttons (6)
and remove the battery pack from the tool. After
recharge, slide the battery pack into tool’s battery
port. A simple and slight pressure will be sufficient.
ASSEMBLy
wARNING:
Always turn off mini drill before
changing accessories, changing collets, or
servicing the tool.
1. FITTING AN ACCESSoRy (See Fig. C)
Keep the spindle lock button (2) depressed. Use the
spanner to slacken the collet nut. Then insert the
shaft of the accessory into the collet nut.
Use the spanner to lightly tighten the collet nut (do
not over tighten).
wARNING:
Do not engage the spindle lock
button while mini drill is running.
2. REPLACING THE CoLLET (See Fig. D)
When using an accessory with a smaller or larger
shaft, i.e.: drills, you will need to change the collet as
detailed below:
Keep the spindle lock button depressed. Use the
spanner to slacken the collet nut. Then remove the
collet nut and old collet and locate the new collet.
After wards restore the collet nut. Finally release the
spindle lock button.
CAUTIoN:
Always use the collet which matches the
shank size of the accessory you plan to use. Do not
force a larger diameter shank into a smaller collet.
3. FITTING A CUTTING/SANDING wHEEL (See Fig. E, F)
Use the cutting disc fixture (13).
First locate mandrel as detailed earlier. Then unscrew
small screw on top of cutting disc fixture.
Insert screw through wheel and screw into mandre.
Do not over tighten, otherwise the wheel may crack.
CAUTIoN:
Always hold the tool away from your face.
Accessories can be damaged during handling and
can fly apart as they come up to speed.
oPERATIoN
1. oN/oFF SwITCH AND DECREASE/INCREASE SPEED
SELECToR (See Fig. G1-G3)
NoTE:
If the On/Off Switch (4) is not at “0” position,
please dial the On/Off Switch to “0”position (See Fig.G1).
Dial the On/Off Switch from “0” position to “2”
position, the tool will start to work. (See Fig.G2)
Continue to Dial the switch to a higher mark, the
speed will increase accordingly. The “10” position is
for the highest speed. (See Fig.G3)
Always choose the correct speed for your work
according to the material. Select the right speed for the
accessory in use. Practice with scrap materiel first.
To stop the tool, dail the switch to “0” position. If
urgent, depress the Quick Stop Button (3) to stop the
tool quickly, and dail the On/Off Switch to “0” position
before restarting the tool. (See Fig.G1)
2. USING ACCESSoRIES
The chart below lists the description, use speed
and scope for some of the small articles supplied
together with the tool by category. To achieve best
performance of the tool, it is strongly recommended
that you read it prior to operation, failure to adhere to
this may cause accessories to fail.
