Rockwell powerflex 700h, Programming Manual

Page: 26 / 104

2-12 Programming and Parameters
SPEED COMMA
N
D
Spd Mode/L
imits
087 [Skip Freq Band]
Determines the bandwidth around a skip
frequency. [Skip Freq Band] is split,
applying 1/2 above and 1/2 below the
actual skip frequency. The same
bandwidth applies to all skip frequencies.
Default:
Min/Max:
Units:
0.0 Hz
0.0/30.0 Hz
0.1 Hz
084
085
086
088 [Speed/Torque Mod]
Selects the torque reference source.
“Speed Reg” (1) - drive operates as a
speed regulator.
Default:
Options:
1
1
“Speed Reg”
“Speed Reg”
053
454 [Rev Speed Limit]
Sets a limit on speed in the negative
direction. Used in bipolar mode only. A
value of zero disables this parameter and
uses [Min Speed] for minimum speed.
Default:
Min/Max:
Units:
0.0 RPM
–[Max Speed]/0.0 Hz
–[Max Speed]/0.0 RPM
0.0 Hz
0.0 RPM
Spe
ed Ref
erenc
es
090 [Speed Ref A Sel]
Selects the source of the speed reference
to the drive unless [Speed Ref B Sel] or
[Preset Speed 1-7] is selected.
(1)
See Installation Manual for DPI port
locations.
Default:
Options:
2
1
2
3-8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
“Analog In 2”
“Analog In 1”
“Analog In 2”
“Reserved”
“MOP Level”
“Reserved”
“Preset Spd1”
“Preset Spd2”
“Preset Spd3”
“Preset Spd4”
“Preset Spd5”
“Preset Spd6”
“Preset Spd7”
“DPI Port 1”
(1)
“DPI Port 2”
(1)
“DPI Port 3”
(1)
“DPI Port 4”
(1)
“DPI Port 5”
(1)
002
091
thru
093
101
thru
107
117
thru
120
192
thru
194
213
272
273
320
361
thru
366
091 [Speed Ref A Hi]
Scales the upper value of the [Speed Ref
A Sel] selection when the source is an
analog input.
Default:
Min/Max:
Units:
[Maximum Speed]
–/+[Maximum Speed]
0.1 Hz
0.01 RPM
079
082
092 [Speed Ref A Lo]
Scales the lower value of the [Speed Ref
A Sel] selection when the source is an
analog input.
Default:
Min/Max:
Units:
0.0
–/+[Maximum Speed]
0.1 Hz
0.01 RPM
079
081
093 [Speed Ref B Sel]
See [Speed Ref A Sel] .
Default:
Options:
11 “Preset Spd1”
See [Speed Ref A
Sel]
090
094 [Speed Ref B Hi]
Scales the upper value of the [Speed Ref
B Sel] selection when the source is an
analog input.
Default:
Min/Max:
Units:
[Maximum Speed]
–/+[Maximum Speed]
0.1 Hz
0.01 RPM
079
093
095 [Speed Ref B Lo]
Scales the lower value of the [Speed Ref
B Sel] selection when the source is an
analog input.
Default:
Min/Max:
Units:
0.0
–/+[Maximum Speed]
0.1 Hz
0.01 RPM
079
090
093
File Gr
oup
No.
Parameter Name & Description Values
Related