Rockwell Automation Allen-Bradley PowerFlex 4 User Manual Download Page 71 | Manualshive

Page: 71 / 94

background image

Appendix

A

Supplemental Drive Information

The tables on the following pages provide drive ratings and
recommended AC line input fuse and circuit breaker information. Both
types of short circuit protection are acceptable for UL and IEC
requirements. Sizes listed are the recommended sizes based on 40 degree
C and the U.S. N.E.C. Other country, state or local codes may require
different ratings.

Fusing

If fuses are chosen as the desired protection method

, refer to the

recommended types listed below. If available amp ratings do not match
the tables provided, the closest fuse rating that exceeds the drive rating
should be chosen.

•

IEC

– BS88 (British Standard) Parts 1 & 2

(1)

, EN60269-1, Parts 1 &

2, type gG or equivalent should be used.

•

UL

– UL Class CC, T or J must be used.

(2)

Circuit Breakers

Refer to listings in the following tables for recommended circuit
breakers (inverse time or instantaneous trip) and 140M Self-Protecting
Motor Starters.

For information on…

See page…

Drive, Fuse & Circuit Breaker Ratings

Drive, Fuse & Circuit Breaker Ratings

(1)

Typical designations include, but may not be limited to the following; Parts 1 & 2: AC,
AD, BC, BD, CD, DD, ED, EFS, EF, FF, FG, GF, GG, GH.

(2)

Typical designations include; Type CC - KTK-R, FNQ-R

Type J - JKS, LPJ
Type T - JJS, JJN

userman.book Page 1 Friday, June 21, 2002 2:48 PM

«
...
69
70
71
72
73
...
»

Summary of Contents for Allen-Bradley PowerFlex 4































































































Reviews:

No comments

Related manuals for Allen-Bradley PowerFlex 4

Brand: Quickmill Pages: 3

Brand: Baader Planetarium Pages: 7

Brand: Beaphar Pages: 2

Brand: Veeder-Root Pages: 27

Brand: Valve Concepts Pages: 18

Brand: K&K Pages: 6

MachXO5-NX Development Kit

Brand: Lattice Semiconductor Pages: 2

Brand: Maclaren Pages: 43

Brand: Lawler Pages: 5

Brand: National Instruments Pages: 14

Brand: National Instruments Pages: 31

Brand: National Instruments Pages: 50

Brand: National Instruments Pages: 24

Brand: National Instruments Pages: 21

Brand: National Instruments Pages: 39

Brand: National Instruments Pages: 22

Brand: National Instruments Pages: 8

Brand: National Instruments Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands