background image

M

OUNTING

 L

OCATION

The mounting location for the Punch X should allow easy access to the controls
for making necessary adjustments. The Punch X will most likely be adjusted only
at the time of installation and will not need further adjustment unless changes to
the audio system are performed. To ensure optimum performance, care should
be taken when mounting the crossover in the following locations:

Engine Compartment

Mounting the Punch X in the engine compartment will

 void your warranty.

 The

only thing that should be mounted in the engine compartment is that big metal
thing that makes the vehicle go fast.

Passenger Compartment Mounting

Mounting the crossover in the passenger compartment will provide easy access
for making adjustments by ear. Select an area which is free from excessive dirt
or dust. If mounting under the seat, be sure the Punch X will avoid misadjustment
from driver or passenger seat movement.

Trunk Mounting

Select an area which will avoid possible damage or misadjustment from loading
and unloading items such as groceries, golf clubs and packages from the trunk.

– 4 –

W

IRING

 

THE

 S

YSTEM

For safety, disconnect the negative lead from the car battery prior to beginning
the installation.

1. Wire the Power Connector

The 

B+

 lead should be connected to a source of non-switched 12 volts DC.

Prepare a length of cable from the co12V by stripping 3/8" of insulation
from the end of the wire. Insert the bared wire into the B+ terminal of the power
connector and fasten the screw.

NOTE: The B+ lead of the audio system MUST be fused 18" or less from
the vehicle's battery. Install a fuseholder, along with the necessary fuse,
under the hood. Connections should be water tight.

The 

REM

 lead should be connected to the remote turn-on or power antenna

output from the source unit. Prepare a length of cable from the source of
switched voltage by stripping 3/8" of insulation from the end of the wire. Insert
the bared wire into the REM terminal of the power connector and fasten the
screw. Total current consumption through this lead is negligible.

Summary of Contents for punch X




















Reviews: