Rockford Fosgate punch X User Manual Download Page 6

– 3 –

I

NSTALLATION

 C

ONSIDERATIONS

This section focuses on some of the vehicle considerations for installing your new
Punch X.  Pre-planning your system layout and best wiring routes will save
installation time.  When deciding how to lay out your new system, be sure that
each component will be easily accessible for making adjustments.

Before beginning any installation, be sure to follow these simple rules:

  1. Be sure to carefully read and understand the instructions before attempting

to install the Punch X.

  2.

For safety

, disconnect the negative lead from the battery prior to beginning

the installation.

  3. For easier assembly, we suggest you run all wires prior to mounting your

Punch X in place.

  4. Route all of the RCA cables close together and away from any high current

wires.

    5. Use high quality connectors for a reliable installation and to minimize signal

or power loss.

  6.

Think before you drill!

  Be careful not to cut or drill into gas tanks, fuel lines,

brake or hydraulic lines, vacuum lines or electrical wiring when working on
any vehicle.

    7. Never run wires underneath the vehicle.  Running the wires inside the vehicle

provides the best protection.

  8. Avoid running wires over or through sharp edges.  Use rubber or plastic

grommets to protect any wires routed through metal, especially the firewall.

  9.

ALWAYS 

protect the battery and electrical system from damage with proper

fusing.  Install the appropriate fuseholder and fuse on the +12V power wire
within 18” (45.7 cm) of the battery terminal.

10. When grounding to the chassis of the vehicle, scrape all paint from the metal

to ensure a good, clean ground connection. Grounding connections should
be as short as possible and always be connected to metal that is welded to
the main body, or chassis, of the vehicle.

The following is a list of tools you will need for installing the Punch X.

Red power wire

Wire strippers

Blue remote turn-on wire

Wire cutters

Black grounding wire

Voltmeter

Electric hand drill w/assorted bits

Jeweler's slotted screwdriver

Battery post wrench

Summary of Contents for punch X




















Reviews: