background image

6

Design Features

illus.-2.1

Power Connector

The power connector allows for quick 

connection and disconnection of the 

amplifier’s Remote, power and ground 

source. The power and ground are 

set-screw wire connectors and will 

accommodate 4 AWG. The remote is 

a set-screw wire connector and will 

accommodate 8 AWG.

Phase Switch

Allows you to select the output 

phase of the amplifier between 0° 

and 180°.

Input Level

Set the Input Level switch to match the outputs of your 

source unit.(LO - RCA or HI - Speaker Level)

Auto Turn On

Three different automatic turn-on modes can be 

selected; REM(+12V), DC Offset, and Audio.

Variable Crossover

Is a built-in 12dB/octave Butterworth 

filter with a crossover point variable from 

50Hz to 200Hz.

Punch Bass

This is an adjustable Bass control 

adjustment variable from 0dB to +12dB 

@ 45Hz.

Power/Protect LED

Power LED illuminates 

blue when the unit 

is turned on. Protect 

LED illuminates red 

if a short circuit or to 

low of an impedance 

is detected at the 

speaker connections. 

The amplifier will 

automatically shut 

down if this occurs.

Remote Punch Level

When connected, the “Gain Control” 

is linked and allows you to remotely 

control the output level of the amplifier 

from the dash or center console.

Audio Input

The RCA/Speaker Harness utilizes either 

speaker level (high-level) or RCA (low-

level) inputs. 

Gain Control

The input gain control is preset to 

match the output of most source 

units.

Summary of Contents for Punch P300-10











Reviews: