PAW-1109-EU(12010)
Be sure to perform depressurizing.
* Omission of depressurizing will cause
water to splash when connecting the body.
Note 19
Reference 4
●
Lightly pull up the suction film unit
to check that the unit is secured
with the hook-and-loop fastener.
Pull up
Depressurizing
Close the water shutoff valve. Then open and close the manual lever on the
water valve to perform depressurizing, and then close the manual lever.
Pull up the connector of the cord from the driving unit close to the water valve section.
This makes installation of the body easier.
See Note 19
[On water shutoff valve side]
6
Connecting Water Supply Hose (continued from previous page)
7
Checking Water Leakage
1. Turn the manual lever on the water valve counterclockwise 180 degrees to
open the water valve. Then open the water shutoff valve fully to supply water.
2. Open and close the manual lever several times to check
that there is no water leaking at connecting sections.
Water is stopped approximately five seconds after the manual lever is closed.
Open
Manual lever
Solenoid valve
For the bonding section
between the water shutoff
valve and wall, lift the ring
shaped cover and the water
supply pipe cover to check
that there is no water leakage.
Manual lever
Close
Open
Attaching Suction Film Unit
Preparing to Connect Toilet Bowl to Body
Attachment drawing
Suction film unit
Air hose connection port
(1) Insert the air hose connection port into the connection port on the front
surface of the suction film unit, and secure these with the clip (medium).
Turn the clip to check (medium) that the clip is engaged with the groove correctly.
10
9
Air hose connection port
Connection port on front surface
of suction film unit
Clip (medium)
Suction film unit
(2) Insert the connection port on the rear surface of the suction film unit into the elbow of the drain until
the connection port contacts the hook-and-loop fastener.
* The suction film unit can be
inserted smoothly by pushing
the section right above the
connection port.
Drain elbow
Connection port on rear
surface of suction film unit
Suction film unit
Suction film unit support
Hook-and-loop fastener
See Reference 4
See Note 14
See Note 14
Remove the cap from the water supply hose immediately
before connecting the hose to the water shutoff valve.
* Dust may enter the water supply
hose during installation, resulting
in water shutoff failure.
Note 17
Connector
①
②
Leakage check sections
Connecting section between water shutoff valve and wall or
fl
oor
Connecting section between water shutoff valve and water supply hose
Solenoid valve
Floor
Connecting section between hoses and water valve
Reference 3
●
When removing the clip, hold the
clip with your fingers and insert a
flat screwdriver
as shown
in the figure
and push it
downward.
Push
Be very careful not to open or
close the manual lever excessively.
* T h e m a n u a l l e v e r m a y b e
damaged.
Note 18
See Note 18
See Note 18
See Note 13
(1) Remove the protection cap from the water supply hose, and insert the
water supply hose into the water supply inlet of the water shutoff valve.
(2) Secure these with the clip (large/silver).
Water supply inlet
Protection cap
(3) After the clip (large/silver) has been attached, turn the clip
to check that the clip is engaged with the groove correctly.
Water shutoff
valve
Clip (large/silver)
Water supply hose
Water supply hose
Click
Bend
See Note 13
See Note 14
See Note 15
See Reference 3
Water shutoff valve
Open
Water shutoff valve
Close
Water shutoff
valve
8
E-Bidet.ru -
официальный
дилер
Roca Lumen Avant
в
РФ
(http://e-bidet.ru)
E-Bidet.ru -
официальный
дилер
Roca Lumen Avant
в
РФ
(http://e-bidet.ru)
