Firmly attach the clip.
* Incorrect attachment will cause water leakage.
Note 13
Attach the clip so that the ends of the
clips are engaged and you hear a click.
* Incorrect attachment will cause water leakage.
Note 15
5
Connecting Flushing Hose to Water Valve
Do not remove the body connection
clip until after checking the water flow.
Body connection clip
Note 11
(4) Secure the water valve frame to the mounting plate of the toilet bowl
with the screws (3 locations).
Water valve frame
Mounting plate
(2) Insert the flushing hose into the water valve spout, and secure these
with the clip (large/white).
(3) After the clip (large/white) has been attached, turn the clip to check
that the clip is engaged with the groove correctly.
(5) Thread the bead chain through the bean chain tube of the water
valve, and hook the manual lever on the water valve.
Manual lever
Hook
* Insert the thin section between beads near the manual lever through the slit into the
bead chain tube, and pull the chain up. The entire bead chain is inserted in the tube.
(1) Remove the protection cap from the water valve spout.
Clip (large/white)
Flushing hose
Water valve
Protection cap
See Note 12 See Note 13
See Note 11
6
Connecting Water Supply Hose
Thread the water supply hose through the hole on the rear of the toilet bowl, and connect this hose to the water valve and the water shutoff valve.
(3) After the clip (large/white) has been attached, turn the clip to check
that the clip is engaged with the groove correctly.
See Note 16
[On toilet bowl side]
(1) Remove the protection cap from the water valve inlet.
(2) Insert the water supply hose into the water valve inlet, and secure these
with the clip (large/white).
Cli
ck
Bend
4
(1) Lift the toilet bowl holding both sides with
two persons.
Toilet bowl
Installing Toilet Bowl
* Be sure to work in two person teams when installing the toilet bowl.
(3) Insert the toilet bowl securing screw into the center hole
at the top of the toilet bowl, and use a
fl
at screwdriver (or
hexagon wrench) to secure the toilet bowl.
See Note 10
Note 8
●
Do not hold the mounting plate
of the toilet bowl.
* Deformation of the mounting plate may
hinder correct connection or correct flushing
of the toilet, or may cause water leakage.
Note 10
Do not tighten the screws too
tightly against the ceramic.
* Doing so may crack the ceramic.
Reference 1
●
Handholds (2 locations) are
provided on the toilet bowl.
Hold the handholds and the
rims to lift the toilet bowl.
Rims
Handholds
Bead chain
tube
Bead chain
Water valve
Do not place the base or drain outlet
of the toilet bowl on the drain socket.
* The socket or packing may be
damaged, causing water leakage.
Note 9
Do not drop the water valve by
mistake.
* The member may be damaged, causing water leakage.
Note 12
See Note 15
Click
Water supply hose
Insert
Water valve inlet
O-ring
Protection cap
Clip (large/white)
Bend
See Note 8
See Reference 1
(2) Insert the drain outlet of the toilet bowl into the center of
the drain rubber joint of the drain socket.
For toilet bowl with heater:
Drain rubber joint
Toilet bowl outlet
Insert
Toilet bowl
See Note 9
See Reference 2
Be careful not to damage the
O-ring.
* Broken or damaged O-ring will
cause water leakage.
Note 14
Reference 2
●
After the drain outlet of the toilet
bowl is inserted into the drain
socket, connect the connector
of the cord from the toilet bowl
and that from the drain socket.
Top view
Toilet bowl
Drain socket
Toilet bowl
Inside when viewed from top
Connector from
toilet bowl
Connector from
drain socket
See Note 14
See Reference 3
Reference 3
●
When removing the clip, hold the
clip with your fingers and insert a
flat screwdriver
as shown
in the figure
and push it
downward.
Push
Attachment drawing
Flushing hose
Water valve
Clip (large/white)
Protection cap
Screw
Screw
See Note 13 See Note 14 See Note 17
See Note 15
See Reference 3
50mm
Toilet bowl securing screw
Floor securing member
Distance between top
surface of ceramic
and top surface of
toilet bowl securing
screw is 50 mm.
After insertion
Do not bend the water supply hose
at a sharp angle or make it too taut.
* The hose may be damaged, causing
water leakage or flushing malfunction.
Note 16
Solenoid valve
Water valve side view
Water valve
inlet
Water valve
spout
Flushing hose
Water shutoff valve
Water supply hose
Hole
Water valve
inlet
Water valve
spout
Water supply hose
Solenoid
valve
Attachment drawing
Water valve side view
E-Bidet.ru -
официальный
дилер
Roca Lumen Avant
в
РФ
(http://e-bidet.ru)
E-Bidet.ru -
официальный
дилер
Roca Lumen Avant
в
РФ
(http://e-bidet.ru)
