background image

PCW-1218A-EU(12010)

Checking posterior washing and bidet washing operation

1. Check the posterior washing operation.

(1) Check that the seat sensor is covered with paper.

(2) Press the [SHOWER] button.

  As the nozzle begins spraying, cover the tip of the nozzle with your hand to prevent water from splashing.

*  Initially it takes approximately one to two minutes until the tank is full and spraying

  is available. (Setting the spray strength to the strongest level shortens this time.)

(3) Press the [STOP] button to stop posterior washing.

* The product is equipped with a seat sensor that 

detects you have sit down on the seat. Posterior 

washing, bidet washing, and deodorizing are not 

activated unless you are sitting on the toilet seat.

  If no paper is attached, cover the seat sensor with 

whitish paper or cloth.

Test Operation (Follow the steps below to conduct test operation when installation is completed.)

2. Check the bidet washing operation similarly.

(1) Hold down the partial flush button and the toilet seat open/close button 

simultaneously for at least 20 seconds.  (When the setting has been 

changed, a beep sounds.)

Hold down these buttons simultaneously for at least 20 seconds.

(2) Prepare seven balls of rolled up 760 mm toilet paper, and put these balls 

in the toilet bowl.  Check that these balls are flushed away in a single 

flushing operation.

If the amount of flushing water is restricted as required in some municipalities, the flushing amount can be 

changed to 8 L for full flush and 6 L for partial flush according to the steps below.

Attaching Decorative Panel and Top Cover

Top cover

Set here

Tab

Tab

Tab

Tab

Decorative panel

Screw

Screw

(2)

 

When fitted onto the body, secure the 
decorative panel with the three screws.

* Be sure to secure the panel with 

screws.

(1) Fit the decorative panel onto the body so that 

the tabs on the decorative panel face the body.

* Be sure to fit the decorative panel so that there is 

no step between the panel and the rear cover.

1. Attach the decorative panel.

2. Attach the top cover.

Open the lid, and check the hot water (shower) temperature and toilet 
seat temperature.

If the water does not flow well, clean the 
strainer. 

(3)  Remove the top cover.

(2)  Operate the open/close handle to 

close the water shutoff valve.

(5)  Separate the mesh part of the 

strainer from the threaded part. 

Wash away any dirt inside the 

mesh part and from the O-ring.

(6)  Attach the strainer to its original 

position.

(7)  Open the water shutoff valve.

(8)  Attach the top cover.

(9)  Insert the power plug into the outlet.

*

  If the water still does not flow well, check the water supply pressure.

If freezing weather is anticipated before handing 
the product to the customer, drain the water.

(2)  Operate the open/close handle to close 

the water shutoff valve.

Do not remove the strainer 

with the water shutoff valve 

open.

* Water will leak from the 

strainer.

Note 8

When attaching the strainers, 

tighten them completely so 

that there is no clearance.

* Incomplete tightening will 

cause water to leak from the 

strainer.

Note 9

(4)  Remove the strainer from the top 

of the body.

Close

Strainer

Strainer

Attach

(3)  Remove the top cover.

(7)  Remove the water supply hose from 

the water shutoff valve, place a wash 

bowl or similar, and drain the wafer 

from the hose.

(8)  Attach the water supply hose to the 

water shutoff valve.

(9)  Firmly attach the strainer.

(11) Attach the top cover.

Water supply hose

Wash bowl

Water shutoff
valve

Clip

Close

Water shutoff valve

(6)  Remove the strainer from the top of 

the body.

Seat sensor

Strainer

Remove

Flat-blade 
screwdriver

Flat-blade 
screwdriver

(10) Turn the manual lever (red) clockwise.

Manual lever (red)

Turn counterclockwise

Flat-blade
screwdriver

Strainer

Remove

(5)  Turn the manual lever (red) 

counterclockwise 180 degrees.

(4)  Drain the water from the hot water tank.

Do not drop the screws into 

the toilet bowl.

* The body must be removed.

Note 7

How to drain water from hot 

water tank

 

Press [MASSAGE] and 

[NOZZLE POSITION / REAR] 

simultaneously for at least two 

seconds to drain the water from 

the hot water tank.

* It takes approximately 20 

seconds until water is drained 

completely.

<Remote control>

Hold down these buttons 

simultaneously for at least two 

seconds.

9

See Note 7

Decorative panel

(1)  Remove the power plug from the outlet.

See Note 8

See Note 9

Water shutoff valve

(1)  Remove the power plug from the outlet.

See Note 8

See Reference 3

See Reference 1

Reference 3

Summary of Contents for LUMEN AVANT 811341000

Page 1: ...ire may result DO NOT USE NEAR WATER Do not use any loose outlet or an ungrounded outlet Electric shock or fire may result PROHIBITED Do not connect the product to any water source other than tap water The inside of the product may be corroded causing an electric shock fire or skin inflammation PROHIBITED Do not remove or insert the power plug with wet hands Electric shock may result NO WET HANDS ...

Page 2: ...Connect Water Supply Hose to Water Valve 3 Be sure to perform depressurizing before removing the body connection clip and the water shutoff cap See in the Installation Manual contained in the toilet bowl package Omission of depressurizing will cause water to splash when the body connection clip and water shutoff cap are moved Note 1 Toilet bowl connectors Body connectors 2 Remove the top cover 3 M...

Page 3: ...et 1 Fully open the open close handle of the water shutoff valve 2 Check that there is no water leakage 1 Operate the remote control to flush the toilet several times 2 Check that there is no water leaking at connecting sections Open Open close handle Water shutoff valve Leakage check sections Bonding section between water shutoff valve and wall or floor Connecting section between water shutoff va...

Page 4: ...eat temperature If the water does not flow well clean the strainer 3 Remove the top cover 2 Operate the open close handle to close the water shutoff valve 5 Separate the mesh part of the strainer from the threaded part Wash away any dirt inside the mesh part and from the O ring 6 Attach the strainer to its original position 7 Open the water shutoff valve 8 Attach the top cover 9 Insert the power p...

Reviews: