ROBOTIQ HAND-E Original Notice Download

Page: 37 / 91

Robotiq Hand-E Gripper - Instruction Manual

kFLT

please refer to your optional controller manual (input registers and status).

Address: Byte 3

Bits

Symbol

gPR

Echo of the requested position for the Gripper, value between 0x00 and 0xFF.

0x00 - Full opening.

0xFF - Full closing.

Address: Byte 4

Bits

Symbol

gPO

Actual position of the Gripper obtained via the encoders, value between 0x00 and 0xFF.

0x00 - Fully opened.

0xFF - Fully closed.

Adress: Byte 5

Bits

Symbol

gCU

The current is read instantaneously from the motor drive, value between 0x00 and 0xFF, approximate current equivalent is 10 * value

read in mA.

Tip

Built-in features like object detection and force control use the fingers' electrical current readings. The user does not need to

create these features.

Summary of Contents for HAND-E




























































































Search results

Summary of Contents for HAND-E

Reviews:

Related manuals for HAND-E

Brands by name

Popular brands

ROBOTIQ HAND-E, Original Notice

Search results

Summary of Contents for HAND-E

Reviews:

Related manuals for HAND-E

Brands by name

Popular brands