7
04/09/2020
INTRODUCTION TO YOUR NEW
Blixer
®
5
g
• Blixer
®
5 V.V.
g
•
Blixer
®
7 • Blixer
®
7 V.V. TABLE-
TOP CUTTER MIXER
ROBOT-COUPE has developed a new concept in
appliance: the
Blixer
®
.
The Blixer
®
combines the features of two well-known
appliances: the cutter and the blender-mixer.
The Blixer
®
is perfectly geared to professional
needs. It can perform any number of tasks which
you will soon discover as you use it.
The Blixer
®
will make it easy to prepare mixed
liquid or semi-liquid, raw or cooked meals.
The Blixer
®
replace the blender which does not
give entire satisfaction because of its incapacity to
process solid foods.
Thanks to its simple design, all components
requiring frequent handling for maintenance or
cleaning are easily fitted or removed.
To make things easier for you, this manual gives a
breakdown of all the various fitting operations.
This manual contains important information designed
to help the user get the most out of their device.
We therefore recommend that you read it
carefully before using your machine.
SWITCHING ON
THE MACHINE
• ADVICE ON ELECTRICAL CONNNECTIONS
Before plugging in, check that your power supply
corresponds to that indicated on the machine’s
identification plate.
• Blixer
®
5 Single phase
ROBOT-COUPE appliances are fitted with the
following types of moto:
230 V / 50 Hz / 1
220 V / 60 Hz / 1
The machine comes with a single phase plug
connected to a power cord.
• Blixer
®
5 V.V. • Blixer
®
7 V.V. Single phase
The models are available with a single phase
motor: + variable speed: 230 V / 50 - 60 Hz /1
The standardized plug must be calibrated to a
minimum of 16 amps and preferably 20 amps, if
the appliance is used intensively.
• ENERGY SAVING MODE FOR Blixer
®
5 - Blixer
®
7
After the food processor is plugged in, it needs to be
switched on by pressing the “on” button I.
If the processor is not used for 5 minutes, it will go
into energy saving mode.
The “on” button needs to be pressed again to switch
on the power supply.
• CONTROL PANEL
Red switch
= Off switch
Green switch I = Start speed 1
Black switch
= Pulse control
Blixer
®
5 - Blixer
®
7 :
Green switch II = Start speed 2
Blixer
®
5 V.V. - Blixer
®
7 V.V. :
Speed variation from 300 to 3,500 rpm.
Blixer
®
5 • Blixer
®
7 Three phase
ROBOT-COUPE appliances are fitted with the
following types of motor:
230-400 V / 50 Hz / 3
400 V / 50 Hz / 3
220 V / 60 Hz / 3
380 V / 60 Hz / 3
This machine is supplied with a cable to which you
simply attach the appropriate electrical plug or
isolator for your system. The cable has four wires,
one earth wire, plus three phases wires.
If you have a 4-pin plug:
1) Connect the green and yellow earth wire to the
earth pin.
2) Connect the three other wires to the remaining
pins.
If you have more than 4 pins in the plug,
please
note the ROBOT-COUPE does not require a neutral
wire.
Switch on the empty machine, making sure that
the blade is rotating properly in an anti-clockwise
direction.
On the motor unit and on the lid a arrow marks the
blade rotation directions.
If the blade turns in a clockwise direction, swap
over two wires.
GREEN YELLOW is the earth,
DO NOT DISCONNECT
Swap either : the
➊
and the
➋
the
➋
and the
➌
the
➊
and the
➌
This appliance must be plugged into an
earthed socket (risk of electrocution).
W A R N I N G
