Robomow Base Station Operating & Safety Manual Download Page 44 | Manualshive

Page: 44 / 56

background image

Message

Displayed

Probable Cause/Event

Corrective/User Action

Rain detected

Press GO

-

Robomow has skipped the last depart due to

rain detection

-

It is not recommended to cut wet or

damp grass, but if you choose to
override the rain sensor, change the
setting of the ‘Rain sensor’ to ‘off’ under
the ‘

Settings

’ menu.

Rain detected

start delayed

-

The operation is delayed as Robomow

detects rain on the scheduled time it should
start the automatic operation from the Base
Station.

-

Do not do anything; the message is

displayed until the Robomow will not
detect rain for x hours (as defined in the
‘

Delay after rain’

menu).

Rain sensor

disconnected

-

Disconnection in the rain sensor wires.

-

Press ‘GO’ to confirm

Ready

keep charging

-

The battery is fully charged (displayed when

charging through the standard power supply
and not through the Base Station)

-

Keep the charger (power supply)

connected and operating

Recharge battery

-

The maximum operating time has been

reached (displayed in non-Base Station
zone)

-

Connect the charger to the mower

Remove fuse

before lifting

-

Robomow was lifted while the battery fuse is

connected.

-

Remove the fuse before lifting

Robomow.

Remove fuse then

check blade

-

Some obstacle is stuck or wrapped around

the blade.

-

Something is preventing a blade from

rotating freely. Severe grass accumulation
under the mowing deck; rope or similar
object wrapped around mowing blade.

-

Object jammed under mower preventing

blade from rotating.

-

CAUTION

– Remove battery fuse

before lifting the mower.

-

Inspect blades for foreign material or

debris preventing rotation.

-

Clean out accumulated grass clippings

using a wooden stick.

Replace blade

every 200 hours

-

An automatic reminder to replace the blades

is displayed every 200 hours

-

Replace the blades and restart the

counter of the blades replacement
reminder by choosing the

‘Blades

replaced – Clear reminder’

option

under the

‘Settings’

menu

Reposition base

-

Robomow fails to enter the Base Station

during ‘Base position’ test

-

Reposition the Base Station; usually it

should be placed with the marked lines
on the Base aligned with the perimeter
wire. If the Base is placed in narrow
pass, where the distance from the
adjacent wire is less than 3 meters, the
Base Station should be placed in shift
of few cm towards out of the lawn.

Splice wire

(Confirm the Base

Station beeps

continuously for cut

wire)

-

Perimeter wire cut

-

Wire disconnected from the Base Station /

Perimeter Switch

-

Confirm wire is plugged in and wire

leads are firmly attached.

-

Walk along perimeter, including islands

and look for obvious cuts or break in
the wire. Repair with Robomow wire
splice connectors.

-

In case the wire cut is not visible call

you service dealer for more information
how to find the wire cut.

-

An unknown fault has occurred and user

help is required

-

Manually drive/carry the mower away

from this particular area and restart
operation.

Start elsewhere

-

Drive wheel motors have been working

under a severe load during automatic or
manual operation.

-

Check to insure the mower is not stuck,

allowing the drive wheels to slip.

-

Check the ground for holes or

indentions, where the mower has
stopped and fill it with dirt and level off.

-

Check the drive wheels are free to

rotate and nothing block them.

-

Remove the mower away from this

particular point and restart operation.

44

«
...
42
43
44
45
46
...
»

Summary of Contents for Base Station

























































Reviews:

No comments

Related manuals for Base Station

Brand: FERREX Pages: 29

Z44 Accu-Z Razor

Brand: Land Pride Pages: 72

Brand: Yazoo/Kees Pages: 46

36V UltraStore 340R

Brand: Flymo Pages: 14

Brand: Sabo Pages: 94

Brand: Yard Pro Pages: 100

Brand: Nakayama Pages: 80

Brand: Cub Cadet Pages: 52

Brand: Wolf Garten Pages: 34

Brand: Wolf Garten Pages: 30

Brand: Jonsered Pages: 56

Brand: Kingfisher Pages: 30

Brand: Exmark Pages: 44

MULTICLIP 11-3203-26

Brand: Stiga Pages: 2

Brand: Jonsered Pages: 19

Brand: Poulan Pro Pages: 30

Brand: Poulan Pro Pages: 30

Brand: Poulan Pro Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands