manualshive.com logo in svg

RoboLabs ROBOPOP 60, Operating Manual, Page: 5 / 39

Share
Download
RoboLabs ROBOPOP 60 Operating Manual Download Page 5

tm2692 Jan-20 

5 

1.4. Power Requirements 

 

CONNECTIONS MUST BE DONE ONLY BY QUALIFIED ELECTRICIAN! 

 

ELECTRIC SOCKET MUST HAVE GROUNDING TERMINAL! 

 

IF SUPPLY CORD DAMAGED, IT MUST BE REPLACED BY MANUFACTURER, SERVICE AGENT, OR 
QUALIFIED PERSONS IN ORDER TO AVOID HAZARD! 

It  is  necessary  to  periodically  check  electric  connections,  including  grounding 
connection. Whenever any fault conditions are found, do not turn the equipment 
and call for qualified electrician! 

Equipotential  bonding  wire  (up  to  10  sq.mm)  shall  be  connected  to  screw 

terminal marked with IEC 5021 sign.

 

 

Cable  plug  is  not  included  in  the  delivery  set.  Use  a  32  A  plug.  Refer  to  the 
wiring diagram on the power cord label. 

It  is  necessary  to  check  electric  wires  and  ground  connection  of  the  machine 
periodically. In case of faults found, an electrician must be called. It is allowed to 
turn the machine on only after all the issues are resolved. 

1.5. Ambient Conditions 

The equipment must be operated at the ambient temperature between 

+5° and 

+40°C (+41°F to +104°F), relative humidity not more than 45% at 40°C/104°F). 
Altitude above sea level should not exceed 1000 m. 

While in operation, a lot of moisture and heat is coming out of the popper. It is 
essential  to  provide  exhausting  hood  (800x800  mm,  750  cu.m/hr  or  more) 
installed above popper’s output port. 

Ambient  conditions  have  strong  effect  on  the  end  product  quality!  See 
section 2.7 for more details!

 

1.6. Safety Components 

EMERGENCY STOP button located on the back side of the machine should be 
used in case of emergency, pressing the button turns machine off immediately. 

 

USING EMERGENCY STOP BUTTON MAY LEAD TO CHAMBER CLOGGING! 

Summary of Contents for ROBOPOP 60








































Reviews:

No comments