background image

19

4. 

As 3, but no spark visible 

Spark availability at electrode during spark period. 

during ignition period. 

Remove the spark lead from the electrode, hold with 
insulated pliers 3mm from earthed metal. If a spark is 
present examine the spark electrode for damage to 
insulation and check the spark gap. If no spark is present, 
check the continuity of the overheat switch and 
connections. If satisfactory the control board is faulty. 

5. 

Heater lights but goes to lock out 

Detection electrode and lead for short to earth. Gas supply 

condition. 

for continuity. 
Air supply blockage. 
Freedom of combustion fan rotor. 
Possible control board fault. 
Polarity of electrical supply. 

SHORT PARTS LIST

Key

No.

G.C.

No.

Part

No.

off

RW No.

Key

No.

G.C.

No.

Part

No.

off

RW No.

Convection Fan Assembly, ITT
13LL RMM/Wx 1596
Combustion Fan: Torin DSA 300
101/2286
Gasket: Combustion Fan
Air Intake Duct
Gasket: Burner Mounting Plate
Injector: (Natural Gas) RW N.9
Electrode Assembly including
Key No. 40
Gasket: Electrode
Solenoid Valve
Gasket: Injector Holder
Pressure Test Nipple Screw
Printed Circuit Board
Electrode

389 283

389 282

203 796
203 797
393 344
203 798
393 570

203 799

203 750
400 001
991 470
204 080

17

26

28
29
32
35
39

40
42A
49
50
65
39A

1

1

1
1
1
1
1

1
1
1
1
1
1
1

71
72
77

78

79A
80
81
82
83
84
85
87
94
99

Control Panel (

)

Overheat Limit Switch Otter V10c
Timer Unit - Sangamo 918801
(WARMPLAN XX AUTO)
Timer Clock Cover
(

 AUTO)

Thermostat Ranco CA6P1916
Control Panel (

 AUTO)

Red Neon Indicator
Amber Neon Indicator
Control Knob
Outer Case Assembly (not illustrated)
Dressing Strip
Bezel for Viewing Window
Gasket - Flue
Cable Clamp

WARMPLAN XX 

WARMPLAN XX

WARMPLAN XX

203 811
393 346
383 561

203 814

385 799
203 815
203 816
203 817
203 818
203 819
203 820
203 821
202 915
203 825

1
1

1

1
1
1
1
1
1
1
1
1
1
1

990965
820953

822125

822126
820954
997914
820956
820955
998786
998575
998982
820968
930611
820752

1
998477

998569
998788
998797
998789
998483

998578
998791
987451
999234
999542
991470
820046

42A

65

17

71

79A

94

40

28

49

29

85

26

80

83

87

50

99

35

72

39

81/82

77

32

39A

78

Summary of Contents for Bantam Ecotherm LPG






















Reviews: