background image

 

 

Operating Instructions 

Controls 

 

 

 

 

 

 

 

 

 

 

 

 

There are five buttons: 

 (Low), 

 (Mid), 

 (High), 

(Lamp), 

 (Power).  

 

1.

 

After connecting to power, indicator light will on, all the output close and the hood will enter standby mode. 

The indicator light will be off automatically after reminding if no operation. 

2.

 

Power on: Press power button once, its indicator light will lit on, the hood works at low speed. Indicator light 

of low speed will be bright. Press power button again to close it, and its indicator light will be off. All the 

function operation of the hood will be closed, the hood enters standby mode, and run by circle. The speed 

buttons and lamp button can work separately and not controlled by the power button. When a certain 

function button is pressed, the hood operates at that function status. Press (Power) button under any status, 

the cooker hood will be switched off without any functions. 

3.

 

Press lamp button once; lights will be turn on. Indicator light of lamp button and power button will on. Press 

lamp button again to turn off the lights. Indicator light of lamp button and power button will be off. And 

recycle like this. 

4.

 

Press the High button once, motor runs on high speed, the indicator light of high button and power button will 

beam. Press high button again and the motor will stop. Indicator light of high button and power button will be 

off and run by circle. 

5.

 

Press the Mid button once, motor runs on middle speed, the indicator light of middle button and power button 

will beam. Press middle button again and the motor will stop. Indicator light of middle button and power 

button will be off and run by circle. 

6.

 

Press the low button once, motor runs on low speed, the indicator light of low button and power button will 

beam. Press low button again and the motor will stop. Indicator light of low button and power button will be 

off and run by circle. 

7.

 

Low speed, mid speed and high speed cannot work at the same time. When hood is on high speed, press low 

speed, it will turn to low speed at once; when it is in low speed, press middle speed, it will turn to middle 

speed immediately, and so on. 

 
 
 
 
 
 
 
 

Summary of Contents for RWD3CL6SSDC














Reviews: