manualshive.com logo in svg

Robin SmartPAT 5500, User Manual

Share
Download
Robin SmartPAT 5500 User Manual Download Page 24

SmartPAT 5500

Press the required control to select the required mode

The display will show which mode is selected:

Professional mode
selected

Press STOP to return to main menu.

Diagnostic test Lockout
This function allows the user to ‘LOCKOUT’ or prevent the selection of manual tests. Only the autotests
are available when this function is selected. This is essentially a safety feature and prevents inadvertent
selection of a manual test when performing auto sequence testing by accidental operation of the keypad.

Set up Diagnostic
test lockout ?     YES/NO

Press YES to perform this function.

Enter access code

….

Enter access code, then press GO, the following is displayed:

Code accepted

After a few seconds the following screen is displayed:

YES lock out, NO
to allow Diagnostics

Press the required control to select the required mode

The display will show the selected mode, locked out or enabled:

Diagnostic tests are
locked out

Press STOP to return to main menu.

Change Access  Code

Change access code ?
YES/NO

Press YES to perform this function.

Enter access code

. . . .

Enter access code, then press GO, the following is displayed:

Now enter new code 

. . . .

On completion press GO. the following is displayed

Re-enter new code

. . . .

23

7681 - 5500 PAT Manual 2002  7/26/02  11:14 AM  Page 25

Summary of Contents for SmartPAT 5500





























Reviews:

No comments

Brands by name

Popular brands

Load more brands