6
Magenta
- magenta flags
Zoom
- a zoom module
Yellow
- yellow flags
Focus
- a focus module
CTO
- CTO flags
HotSpot
- a fine movement of reflector
Static Gobo
- a static gobo wheel
Dimmer 1
- a dimmer lamella
Rot. Gobo Wheel
- a carousel of rotating gobos
Dimmer 2
- a dimmer lamella
R. Gobo Index
- an indexing of rotating gobo
By using these items you can calibrate and adjust effects to their right positions.
Calibration via the control board
1. Disconnect DMX controller from the fixture and enter the "Calibrate Effects" menu.
2. Use the [up arrow] and [down arrow] to find desired effect and touch it to enter the fine effect adjustment
screen.
3. Set desired value and save it by touching the [confirm].
4. Repeat steps 2 and 3 for the next effects.
5. After calibrating all effects, touch the [confirm] to save all adjusted values and reset the fixture.
Calibration via the DMX controller
1. Connect DMX controller to the fixture and set fixture effects to the desired positions before fine calibration.
2. Enter the "Calibrate Effects" menu and now you can exactly calibrate desired effects by DMX controller.
There is a calibration protocol:
Effect
Mode 1
Mode 2
Mode 3
Pan
channel 33
channel 26
channel 24
Tilt
channel 34
channel 7
channel 5
Colour wheel
channel 35
channel 28
channel 26
Cyan
channel 36
channel 29
channel 27
Magenta
channel 37
channel 30
channel 8
Yellow
channel 38
channel 31
channel 29
CTO
channel 3
channel 3
channel 30
Static Gobo
channel 40
channel 33
channel 31
Rot. Gobo Wheel
channel 41
channel 34
channel 32
Rot. Gobo Index.
channel 42
channel 35
channel 33
Prism
channel 43
channel 36
channel 34
Iris
channel 44
channel 37
channel 35
Zoom
channel 45
channel 38
channel 36
Focus
channel 46
channel 3
channel 37
Hot-Spot
channel 47
channel 40
channel 38
Dimmer
channel 48
channel 4
channel 3
Dimmer
channel 4
channel 4
channel 40
After having calibrated all effects, touch the [confirm] to save adjusted values and reset the fixture.
Load Default Calibrations
- The item loads default (factory) calibration values.
Updating software
-
The menu item allows you to update software in the fixture via either serial or USB port
of PC.
The following are required in order to update software:
- PC running Windows 95/98/2000/XP or Linux
- DMX Software Uploader
- Flash cable RS232/DMX No.13050624 (if you want to use a serial port of PC)
- Robe Universal Interface (if you want to use an USB port of PC)
Note 1: Software update should execute a qualified person. If you lack qualification, do not attempt the updatey
-
ourself and ask for help your ROBE distributor.
Note 2: DMX address, IP address, programs 1-3 and all items in the menu "Personality" will be set to their
default (factory) values.
To update software in the fixture:
I. Installation of the DMX Software Uploader.
1. DMX Software Uploader program is available from the ROBE web site at WWW.robe.cz.
2. Make a new directory ( e.g. Robe_Uploader) on your hard disk and download the software to it.
3. Unpack the program from the archive. If the Robe fixture is produced in both magnetic
and electronic ballast version, name of DMX Software Uploader is the same for both versions.
II.Fixture software updating.
1.Determine which of your ports is available on your PC and connect it:
- with the DMX input of the fixture if you using the flash cable RS232/DMX
Summary of Contents for 300E Spot
