manualshive.com logo in svg

Roberts Gorden GordonRay BH-100, Instructions Manual

Share
Download
Roberts Gorden GordonRay BH-100 Instructions Manual Download Page 6

2

GORDONRAY

®

BH SERIES HEATER

This symbol is used throughout the manual to notify
you of possible fire, electrical or shock hazards. Please
pay special attention when reading and following the
warnings in these sections.

Due to the nature of gas conversions, it is important
you use the correct conversion kit for the heater model
and the gas you are converting to.

Heater Safety

Your Safety
is Important
to Us

Important
Notice

In Canada:

The conversion shall be carried out in accordance with
the requirements of the provincial authorities having
jurisdiction and in accordance with the requirements of
the CAN1-B149.1 and .2 installation codes.

WARNING

Use only genuine ROBERTS GORDON   conversion kits.

Failure to follow these instructions will result in
death, injury or property damage.

®

WARNING

Service and annual inspection must be done by a
contractor qualified in the installation and service of
gas-fired heating equipment.

Failure to follow these instructions will result in death,
injury or property damage.

Summary of Contents for GordonRay BH-100
























Reviews:

No comments

Brands by name

Popular brands

Load more brands