manualshive.com logo in svg

Roberts Gorden GordonRay BH-100, Instructions Manual

Share
Download
Roberts Gorden GordonRay BH-100 Instructions Manual Download Page 10

6

GORDONRAY

®

BH SERIES HEATER

NOTE: The burner may be removed to a workbench or converted in place.

a. Turn off gas supply valve, disconnect gas from burner.

b. Turn off power supply and disconnect wires from burner.

c. Unplug thermostat wires from burner.

d. If outside air is installed, disconnect.

e. Remove the (4) bolts which hold the burner on the transition 

tube using a 1/2" wrench.

f.

Remove the burner. Refer to 

Page 6, Figure 3.

g. Save the Gasket (P/N 02568200) or re-install a new one after 

conversion.

Step 1

Fuel Conversion Instructions

WARNING

Burner is secured to transition tube by Bolts and
Lockwashers.

Upon removal of Bolts, Burner is free from Transition
Tube and will fall if not supported.

Failure to follow these instructions will result in death,
injury or property damage.

Burner (shown with tube gasket)

Gasket

Transition Tube

Bolts & Flatwashers (4)

FIGURE 3. GORDONRAY

®

BH Assembly Overview

Summary of Contents for GordonRay BH-100
























Reviews:

No comments

Brands by name

Popular brands

Load more brands