Robe Robin 1200 User Manual Download Page 37

Page: 37 / 43

Battery backup of the touch screen

Readout fixture usage, receiving DMX values, temperatures, etc

Built-in analyzer for easy fault finding, error messages

Built-in demo sequences

Theatre mode for silent pan/tilt and zoom moving

Silent fans cooling,

Stand-alone operation

3 user editable programs, each up to 100 steps

Supported protocols: USITT DMX 512, RDM, ArtNet, MANet, MANet2

Support of RDM (Remote Device Management)

6 DMX modes (45, 21, 15, 10, 45 and 37 control channels)

Wireless DMX/RDM module

Compliance with USITT DMX-512 (1986 & 1990) and 512-A

Full DMX fidelity and frame integrity

Auto sensing of DMX frame rate and frame size

<5ms DMX latency

Operational frequency range of 2402-2480 MHz

Producer: LumenRadio

Connection

DMX data in/out: Locking 3-pin and 5-pin XLR

AC power input: 1.5 m power cord without plug

Ethernet: RJ45

Rigging

Mounting points: 2 pairs of 1/4-turn locks

Mounting horizontally or vertically via 2 Omega brackets

Temperatures

Maximum ambient temperature: 45° C

Maximum housing temperature: 80° C

Minimum distances

Min. distance from flammable surfaces: 1 m

Min. distance to lighted object: 1.5 m

Total heat dissipation

BTU/h (calculated)

Accessories

2 x Omega holder (No.99010420)

1 x EggCrate Robin 1200 LEDWash-black (No. 19520091)*

1 x EggCrate Robin 1200 LEDWash-white (No. 19620091)*

* only one EggCrate is enclosed according fixture housing colour

Optional accessories

Top hat-black (No.10980112)

Weight (net)

8. kg

Summary of Contents for Robin 1200












































Search results

Summary of Contents for Robin 1200

Reviews:

Related manuals for Robin 1200

Brands by name

Popular brands

Robe Robin 1200, User Manual

Search results

Summary of Contents for Robin 1200

Reviews:

Related manuals for Robin 1200

Brands by name

Popular brands