7
6.7 Reset
This option enables the Robin 100 LEDBeam to index all effects and return to their standard positions.
6.8 Special functions (Special)
RDM Low
-
This menu item shows the first part of the RDM identification code
.
RDM High
-
This menu item shows the second part of the RDM identification code.
Wireless
-
Wireless DMX information
. The menu allows to read some information about
Wireless DMX operation
Stat
-
Wireless status
. Use the menu to read wireless DMX status.
Unlink
- use this item to unlink fixture from wireless DMX.
Adjust
-
Adjustment
. The menu allows the fine adjustment of effects.
DMX Val
-
DMX values
. Use the menu to set DMX values of fixture´s channels.
Calib
- calibration of white colour.
Cal P/T
- Use this menu to calibrate pan/tilt positio.
Cal Col
- Use this menu to set white colour 5600K.
Calibration of the pan/tilt via the control board
1. Disconnect DMX controller from the fixture and enter the "Cal P/T" menu.
2. Use the [PREV] and [NEXT] to find "Pan" and press [ENTER].
3. Set desired value and save it by pressing [ENTER].
4. Repeat steps 2 and 3 for Tilt.
5. After calibrating both effects, find item "Store" and press [ENTER]. to save all adjusted values and reset the
fixture.
Calibration of the white 5600K via the control board
1. Disconnect DMX controller from the fixture , open the sShutter and Dimmer and set the Virtual colour wheel
channel at DMX=10 (white 5600K). Aim the light beam on the lux meter (e.g. Minolta CL-200A Chroma meter)
which is placed cca 5m from the fixture.
2. Set the menu item Colour Calibration Mode to On (Pers-> C Cal M -> On).
3. Enter the menu "Cal Col".
4. Use the [NEXT] or [PREV] button to select desired colour and press
the [ENTER] button.
5. Use the [NEXT] or [PREV] button to set desired value of colour.
5. By means of the "Red C, Grn C, Blue C and Whi C" items adjust the 5600K colour temperature
as exactly as possible (∆u´v´= 0).
7. After adjusting 5600K colour temperature, select item Store and press the [ENTER] button to save all
adjusted values .
Note: you can also use DMX controler for both calibrations stated above, calibration protocol is the following:
Effect
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Pan-fine adjustment
channel 36
channel 20
channel 15
channel 10
channel 36
Tilt - fine adjustment
channel 37
channel 21
channel 16
channel 11
channel 37
Red - red saturation
channel 38
channel
channel 7
channel
channel 38
Green- green saturation
channel 39
channel 3
channel 8
channel 3
channel 39
Blue - blue saturation channel 40
channel 24
channel 19
channel 14
channel 40
White - white saturation channel 41
channel 25
channel 20
channel 15
channel 41
Cal Load
- Loads default (factory) calibration.
Sw Upd
-
Software update
. The menu item allows you to update software in the fixture via either serial or
USB port of PC.
The following are required in order to update software:
- PC running Windows 95/98/2000/XP/7 or Linux
- Update software
- Flash cable RS232/DMX No.13050624 (if you want to use a serial port of PC)
- Robe Universal Interface (if you want to use an USB port of PC)
Note 1: Software update should execute a qualified person. If you lack qualification, do not attempt the update
Summary of Contents for Robin 100 LEDBeam Wireless DMX CRMX
