Robe Anolis E-box Remote Basic User Manual Download Page 20

Page: 20 / 20

9. Disposing of the product

To preserve the environment please dispose or recycle this product at the end of its life according to the local
regulations and codes.

10. Change Log

This section summarizes changes in the user manual.

Version of the

manual

Date of issue

Description of changes

1.1

26/01/2022

Description of connection blocks modified

1.2

24/02/2022

Description of the fixture corrected

1.3

14/03/2022

Design of the manual changed

1.4

07/04/2022

Menu DMX preset added, menu Devices removed, Eminere connection changed

April 7, 2022

Specifications are subject to change without notice.
Copyright © 2021-2022 Robe Lighting - All rights reserved

Made in CZECH REPUBLIC by ROBE LIGHTING s.r.o. Palackeho 416/20 CZ 75701 Valasske Mezirici

Summary of Contents for Anolis E-box Remote Basic





















Search results

Summary of Contents for Anolis E-box Remote Basic

Reviews:

Related manuals for Anolis E-box Remote Basic

Brands by name

Popular brands

Robe Anolis E-box Remote Basic, User Manual

Search results

Summary of Contents for Anolis E-box Remote Basic

Reviews:

Related manuals for Anolis E-box Remote Basic

Brands by name

Popular brands