ROBBE Corsair ARF FW004006 Building And Operating Instructions Download Page 6

Specification:

Wingspan:  

1200 mm

Length:  

970 mm

All-up weight:  

1600 g

Height:  

max. 330 mm

Wing area:  

28 dm

2

Wing loading:  

57g/dm

2

Scale:  

1:10.5

Battery:  

4S / 2600 mAh

Recommended accessories:

T6J-R2006GS 2.4 GHz FHSS   1 x F4100
Roxxy-Power 4S 2650 mAH  

1 x 6932

T-socket  

1 x 8895

Essential tools and adhesives:

Pointed-nose pliers
Balsa knife
Cross-point screwdriver
Ropoxi 5-minute epoxy
Polystyrene cement
Adhesive tape
Abrasive paper

Set contents

1)  Accessory set (10 x control surface horns, 1 x aerial set, 4 replacement hinges, 3 x 

wing retaining screws, M4 x 60, screwdriver, 4 x clevises, 2 x aileron pushrods and 
clevises, 2 x flap pushrods and clevises)

2)   Rudder with pre-glued hinges
3)  Tailplane unit with pre-glued hinges
4)   4-blade propeller, 13" x 6"
5)   Fuselage with power system installed, retractable tailwheel, electronic retract unit, ele-

vator servo, rudder servo, tailwheel steering servo

6)   Wing set with main retract units installed, aileron and flap servos, cable loom with com-

mon connector

6

Building and Operating Instructions - Corsair ARF 

No. FW004006

Summary of Contents for Corsair ARF FW004006





















Reviews: