RKI 65-2443SS Series Operator'S Manual Download Page 19

Page: 19 / 20

65-2443SS-XX PPM Hydrogen Transmitter • 19

Parts List

Table 6 lists replacement parts and accessories for the ppm hydrogen transmitter.

Table 6:Parts List

Part Number

Description

07-7151RK

O-ring for junction box

10-5153RK

Lid locking set screw for junction box

18-0416RK-11

Junction box with cover, stainless steel

33-2001RK-01

Humidifier tube w/3/16” tubing on ends, for calibration kit

57-1070-01

Amplifier (specify target gas and detection range)

61-0160RK

PPM hydrogen detector, for all ranges

65-2443SS-500

0 - 500 ppm hydrogen transmitter (includes detector and amplifier)

65-2443SS-1000

0 - 1,000 ppm hydrogen transmitter (includes detector and amplifier)

65-2443SS-2000

0 - 2,000 ppm hydrogen transmitter (includes detector and amplifier)

71-0549

65-2443SS-XX PPM Hydrogen Transmitter Operator’s Manual

(this document)

81-0000RK-01

Calibration cylinder, 1,000 ppm hydrogen in air, 34 liter steel

81-0000RK-03

Calibration cylinder, 1,000 ppm hydrogen in air, 103 liter

81-0000RK-21

Calibration cylinder, 2,000 ppm hydrogen in air, 34 liter steel

81-0000RK-23

Calibration cylinder, 2,000 ppm hydrogen in air, 103 liter

81-0000RK-71

Calibration cylinder, 500 ppm hydrogen in air, 34 liter steel

81-0000RK-73

Calibration cylinder, 500 ppm hydrogen in air, 103 liter

81-0032RK-01

Calibration cylinder, 250 ppm hydrogen in air, 34 liter steel

81-0032RK-03

Calibration cylinder, 250 ppm hydrogen in air, 103 liter

81-1050RK

Regulator, 0.5 LPM, with pressure gauge and flow control knob, for 17 liter and 34

liter steel calibration cylinders (cylinders with external threads)

81-1051RK

Regulator, 0.5 LPM, with pressure gauge and flow control knob, for 34 liter aluminum,

58 liter, and 103 liter steel calibration cylinders (cylinders with internal threads)

81-1117RK

Calibration cup

81-F072RK

Calibration kit, includes regulator, humidifier tube, calibration cup, 103 liter 1,000 ppm

hydrogen calibration cylinder, and 103 liter 2,000 ppm hydrogen calibration cylinder

81-F072RK-LV

Calibration kit, includes regulator, humidifier tube, calibration cup, 34 liter 1,000 ppm

hydrogen steel calibration cylinder, and 34 liter 2,000 ppm hydrogen steel calibration

cylinder

Summary of Contents for 65-2443SS Series





















Search results

Summary of Contents for 65-2443SS Series

Reviews:

Related manuals for 65-2443SS Series

Brands by name

Popular brands

RKI 65-2443SS Series, Operator'S Manual

Search results

Summary of Contents for 65-2443SS Series

Reviews:

Related manuals for 65-2443SS Series

Brands by name

Popular brands