manualshive.com logo in svg

RKI 65-2437RKSS-05, Operator'S Manual, Page: 18 / 18

Share
Download
RKI 65-2437RKSS-05 Operator'S Manual Download Page 18

 

 14 • 65-2437RKSS-05 CO Detector

Parts List

Table 5 lists replacement parts and accessories for the CO detector.

Table 3: Parts List

Part Number

Description

06-1248RK

Sample tubing (order by the foot)

07-0033RK

Detector housing cap gasket

07-0203RK

Rubber retaining boot (for charcoal filter)

07-7151RK

O-ring for junction box

10-5153RK

Lid locking set screw for junction box

18-0416RK-11

Junction box with cover, stainless steel

33-7101RK

Charcoal filter disk

65-2437RKSS-05

CO detector/j-box, CSA classified

65-2438

CO detector (with plug-in sensor)

71-0439

65-2437RKSS-05 CO Detector Operator’s Manual (this document)

81-0064RK

Calibration cylinder, 50 PPM CO in air, 17 liter

81-0064RK-01

Calibration cylinder, 50 PPM CO in air, 34 liter steel

81-0064RK-03

Calibration cylinder, 50 PPM CO in air, 103 liter

81-0076RK

Zero air calibration cylinder, 17 liter

81-0076RK-01

Zero air calibration cylinder, 34 liter steel

81-0076RK-03

Zero air calibration cylinder, 103 liter

81-1050RK

Regulator with gauge and knob, 0.5 LPM, for 17 liter and 34 liter steel 
calibration cylinders (cylinders with external threads)

81-1051RK

Regulator with gauge and knob, 0.5 LPM, for 34 liter aluminum, 58 
liter, and 103 liter calibration cylinders (cylinders with internal threads)

81-1117RK

Calibration cup

ES-1531-CO

CO replacement sensor

Summary of Contents for 65-2437RKSS-05



















Reviews:

No comments