background image

 

RP-2009 Pump for the GX-2009

  13

Alarms

The table below outlines the alarms that may occur on the RP-2009.

Maintenance

Replacing The Battery

1. Locate the black plastic battery cap on one end of the pump unit.

2. Push down and rotate battery cap counterclockwise until it stops, 1/4 

of a turn.

3. Pull the battery cap away from the pump unit.

4. Remove the old battery from the pump unit. It will slide right out.

5. Insert the new b end first into the pump unit. Use an AA 

alkaline. The battery orientation is shown on the bottom of the pump 
unit.

6. Slide the battery cap over the battery onto the pump unit, push it down 

and turn it clockwise unit is stops beneath the instrument release tab.

Replacing the Cotton Dust Filter

1. Locate the clear plastic filter holder at one end of the pump unit. 

2. Grasp the ridged sides of the filter holder and turn it 1/4 of a turn 

counterclockwise.

Alarm Type

Visual 

Indications

Audible 

Indications

Other 

Indications

Recommended 

Action

Low Battery

POWER 

LED flashing

none

none

Replace the battery.

Dead Battery

POWER 

LED flashing

constant 

buzzer

none

Replace the battery.

Low Flow

NOTE: A low flow alarm 
may get combined with a 
low or dead battery 
alarm since a low battery 
voltage may cause the 
pump to stop working.

LOW FLOW 

LED flashing

intermittent 

buzzer

pump stops

• Check the rubber 

sample nipple and 

filters to make sure 

they are clear.

• If a hose and probe 

are used, check 

them for kinks or 

obstructions.

• Press and release 

the POWER button 

to reset the alarm.

• If the low flow 

condition persists, 

the pump may need 

servicing.

Summary of Contents for RP-2009
















Reviews: