RKI Instruments 04 Series Operator'S Manual Download

Page: 82 / 98

82 • Appendix A: Maintenance Mode

SC-04

Turning the Zero Suppression On/Off (ZERO.SUP)

The

ZERO.SUP

setting is not intended for field adjustment. The default setting is

Turning the Zero Follower On/Off (ZERO.FLW)

The

ZERO.FLW

setting is not intended for field adjustment. The default setting is

User Mode Zero Suppression (ZSUP.DSP)

: Zero suppression item appears in User Mode.

OFF

(factory setting): Zero suppression item does not appear in User Mode. The zero

suppression item is always available in Maintenance Mode.
It is not normally necessary to have the zero suppression item appear in User Mode. Contact

RKI Instruments before turning this setting on.

User Mode Zero Follower (ZFLW.DSP)

: Zero follower item appears in User Mode.

OFF

(factory setting): Zero follower item does not appear in User Mode. The zero follower

item is always available in Maintenance Mode.
It is not normally necessary to have the zero follower item appear in User Mode. Contact RKI

Instruments before turning this setting on.

Cylinder Setting (CYL.DISP)

CYL SEL

item appears in User and Maintenance Modes’

GAS CAL

item.

OFF

(factory setting):

CYL SEL

item does not appear in User and Maintenance Modes’

GAS CAL

item.

Sensor

Zero Suppression Value

0.10 ppm

HCN

0.5 ppm

4 ppm

0.30 ppm

0.02 ppm

0.20 ppm

Summary of Contents for 04 Series



































































































Search results

Summary of Contents for 04 Series

Reviews:

Related manuals for 04 Series

Brands by name

Popular brands

RKI Instruments 04 Series, Operator'S Manual

Search results

Summary of Contents for 04 Series

Reviews:

Related manuals for 04 Series

Brands by name

Popular brands