RiTTO TWINBUS System Manual Download Page 149

Page: 149 / 197

Installation: Assembly, connection and start-up

149

tio

2.8.8 Built-in colour camera 1 4883

Assembly

Remove the TwinBus device and the supplied components from the packaging.

Connection

Connection to TwinBus video line and feed from mains transformer 1 6477.

Connection to 75

coaxial video line and feed from mains transformer 1 6477.

Starting up

No start-up is required.

Installation diagram for installing on two M 3 x 10 stud bolts.

Installation with stud bolts.

Note:

The camera can also be stuck on using the provided adhesive tape.

107

15,5

00308-0

TOP

OBEN

00309-0

1 2 3

80 81 Va Vb

1 2 3

80 81 Va Vb

1 6477

1 4883

))

S0074-3

Summary of Contents for TWINBUS






































































































































































































Search results

Summary of Contents for TWINBUS

Reviews:

Related manuals for TWINBUS

Brands by name

Popular brands

RiTTO TWINBUS, System Manual

Search results

Summary of Contents for TWINBUS

Reviews:

Related manuals for TWINBUS

Brands by name

Popular brands