manualshive.com logo in svg

Rittal 3214.700, Assembly And Operating Instructions Manual, Page: 17 / 20

Share
Download
Rittal 3214.700 Assembly And Operating Instructions Manual Download Page 17

Rittal HD air/water heat exchangers

17

14 Appendix

EN

14.2 Cut-out and hole sizes

Fig. 21:

Cut-out and hole sizes, 3214.700 and 3215.700

3214.700

3215.700

(220)

199
186

24,6

215

193

140

Ø7(10x)

200

230

230

300

165

981,9

230

230

306

98

170

19,1

28,1

337395 / A06271300SKA1

180

5 X 45˚

18,6

184

155

Ø7(6x)

14,5 X

(525,7)

273

331

188

Ø12(2x)

119

35

170

337394 / A06210500SKA3

top

top

SK 3214.700

Assembly instructions for air/water heat exchanger
1.  Prior to drilling and cutting, check the dimensions of the drilling template.
2.  Stick the drilling template onto the side panel or door of the enclosure using  
 adhesive 

tape.

3.  Mark, drill and deburr the holes.
4.  Make the cut-outs including the line width and deburr the cut-outs.
5.  Install gasket in the unit
6.  For mounting, attach the air/water heat exchanger using 6 threaded pin  
 

M6x30, washers A6.4 and nuts M6

SK 3215.700

Assembly instructions for air/water heat exchanger
1.  Prior to drilling and cutting, check the dimensions of the drilling template.
2.  Stick the drilling template onto the side panel or door of the enclosure using  
 adhesive 

tape.

3.  Mark, drill and deburr the holes.
4.  Make the cut-outs including the line width and deburr the cut-outs.
5.  Install gasket in the unit
6.  For mounting, attach the air/water heat exchanger using 10 threaded pin  
 

M6x30, washers A6.4 and nuts M6

45°

Summary of Contents for 3214.700





















Reviews:

No comments