Page 11
For assistance, call RITRON at 800-872-1872, or go to www.ritron.com
qtm9322b.pm5
PROGRAMMING HOW MANY TIMES YOUR
RECORDED VOICE PHRASES ARE
REPEATED IN EACH TRANSMISSION
PROGRAMMING A BROADCAST
SCHEDULE FOR SWITCH STATUS
TRANSMISSIONS
What is the purpose of programming a Broadcast
Schedule for Switch Status Transmissions?
You can
program different switch status transmission schedules for
the open condition, and for the closed condition of your
switch.
Example:
The switch status message for
switch
open
is "Pump motor temperature OK". You may
schedule the Quick Talk to transmit this message
once every two hours; this way, you know the Quick
Talk is operating properly.
If the corresponding switch status message for
switch
closed
is "Pump Motor Over Temperature", you may
schedule the Quick Talk to broadcast this message
every two minutes, so the situation would receive
prompt attention.
Do I need to program this feature?
The Quick Talk is
set at the factory to transmit a switch status message one
time with each switch change. If this is sufficient for your
application, you can skip to the next section.
To Program a Broadcast Schedule of Switch Status
Transmissions for the Switch Open Condition:
1. Pick up the telephone receiver; listen for the tone.
2. Dial "
511
", then dial the one-digit code number from
Table 5 below.
The Factory Default is "
511-1
", which means the
transmission is sent one time when the switch
changes to open condition.
Wait for the confirmation beep after dialing.
3. Hang up the telephone or continue programming.
To Program a Broadcast Schedule of Switch Status
Transmissions for the Switch Closed Condition:
1. Pick up the telephone receiver; listen for the tone.
2. Dial "
512
", then the one-digit code number from
Table 5.
The Factory Default is "
512-1
", which means the
transmission is sent one time when the switch
changes to closed condition.
Wait for the confirmation beep after dialing.
3. Hang up the telephone or continue programming.
What is the purpose of setting the number of times the
Voice Phrase is repeated in each Transmission?
Your
previously recorded voice phrase can be programmed to
repeat from one time to nine times in each Quick Talk radio
transmission, depending on how you program this feature.
More urgent messages may have more phrase repeats.
Example:
You previously recorded the message "Pump
Motor Hot", then programmed Quick Talk to repeat the
phrase two (2) times in each transmission. In this case,
activating the switch results in the Quick Talk transmitting:
"...
beep
.
Pump motor hot. Pump motor hot.
beep
..."
The beginning and ending beeps are added automatically
to attract attention to Quick Talk transmissions.
Do I need to program this feature?
The Quick Talk is
set at the factory to play each recorded voice phrase one
time in each transmission. If this is sufficient for your
application, you can skip to the next section, in which we
explain how to program the transmission itself to be
repeated at different intervals.
To Program the Number of Times the Switch Open
Phrase is Repeated in Each Transmission:
1. Pick up the telephone receiver; listen for the tone.
2. Dial "
711
" then a single digit indicating how many
times you want the voice phrase repeated in each
transmission, as shown in Table 4.
Example:
To repeat the phrase three times, dial
"
711-3
".
Wait for the confirmation tone after dialing.
3. Hang up the telephone or continue programming.
To Program the Number of Times the Switch Closed
Phrase is Repeated in Each Transmission:
1. Pick up the telephone receiver, listen for the tone.
2. Dial "
712
", then a single digit indicating how many
times you want the voice phrase repeated in each
transmission, as shown in Table 4.
Example:
To repeat the phrase five times, dial
"
712-5
".
Wait for the confirmation tone after dialing.
3. Hang up the telephone or continue programming.
TABLE 4
VOICE PHRASE REPEATS
CODE
IN EACH TRANSMISSION
NUMBER
1 time
.............................
1
2 times
............................
2
3 times
............................
3
4 times
............................
4
5 times
............................
5
6 times
............................
6
7 times
............................
7
8 times
............................
8
9 times
............................
9
TABLE 5
CODE
MESSAGE SCHEDULE
NUMBER
Never send messages for this condition
....
0
On switch condition change only
........
1
Every 30 seconds
.....................
2
Every (1) minute
......................
3
Every (2) minutes
.....................
4
Every (5) minutes
.....................
5
Every (10) minutes
....................
6
Every (30) minutes
....................
7
Every (1) hour
........................
8
Every (2) hours
.......................
9
DEFAULT
DEFAULT
All manuals and user guides at all-guides.com
