Section
3
Programming
18
13
3.5
Program Loudmouth
™
Features
The wireless speaker can be field programmed for a variety of features. Refer to
Table 5
for the two digit codes
available for field programming. In our example we will program an LM-U450 for Record and Play operation. The
Loudmouth
™
is set from the factory with these
√
options
enabled.
1. Refer
to
Table 5
to determine the two-digit feature code and write it down.
2. Press
and
HOLD
the
PROGRAM
button (See
Loudmouth
™
receiver assembly
on page 2
for location). A "P" will appear on the program display as you enter program mode and the
radio will beep rapidly.
3. Release
the
PROGRAM
button after the beeping has stopped. The radio will emit a triple
beep indicating that the radio is in program mode and a hyphen will appear on the program
display.
4. Scroll to the character “A” by clicking the
PROGRAM
button until the program display
shows the correct character.
Pause
—the radio will sound a low tone and show a hyphen
across the center of the display to indicate that it is ready to accept the first digit of the
Feature code.
5. Enter the 1
st
digit of the feature code by clicking the
PROGRAM
button until the program
display shows the desired number.
Pause
—the radio will sound a low tone and show a
hyphen across the center of the display to indicate that it is ready to accept the next digit.
6. Enter the 2
nd
digit of the feature code by clicking the
PROGRAM
button until the program
display shows the desired number.
Pause
—the radio sounds a low tone and will show a
hyphen across the center of the display to indicate that it is ready to accept the next digit.
7. Press and release the
ENTER
button to save your programming. A triple beep will sound to
indicate that programming was successful and a hyphen will appear on the program
display. The radio is now ready for another program entry.
NOTE: An error tone will sound if you attempt to save an incorrect code, an "E" will appear
on the display. Check the digits you are attempting to enter, then re-enter.
8. Once you have made your final program entry, press the
ENTER
button a final time to exit
programming mode. The Program display will be blank and the radio will be ready for use.
The Loudmouth
™
will exit program mode automatically after 30 seconds if no program
entries are attempted.
Table
5:
Loudmouth
™
Feature Codes
Code
Feature
Default
Description
Special Features
21
Reset to Factory Defaults
Resets Wireless Speaker to Factory default programming.
22
Display Radio Revision
Loudmouth
™
will display a sequence of 6 digits to identify operating code
revision. This is helpful when troubleshooting the radio.
23
Pre-Announce Tone – On
√
Enable this feature to play a short tone over the Loudmouth
™
speaker
whenever it receives a signal.
24
Pre-Announce Tone – Off
Disable Pre-Announce Tone
25
Record and Play – On
When set received messages are recorded and played back over the
Loudmouth
™
speaker immediately after the received signal is removed.
26
Record and Play – Off
√
Disable Record and Play feature
27
One
Speaker
√
Set when one speaker is used for maximum available volume.
28
Two Speakers
Set when two speakers are used for maximum available volume.
29
Weather Alert – On
Enable this feature to receive local NOAA weather radio emergerncy
broadcasts from the National Weather Service and play them over the
Loudmouth
™
speaker. This feature is only available on the LM-V150.
20
Weather Alert – Off
√
Disable
Weather
Alert
Battery Powered Operation
41
Battery Operation – On
Set to extend battery life when powering the Loudmouth
™
with an external
battery.
42
Battery Operation - Off
√
Set when powering the Loudmouth with the RPS-1A or an external DC
supply.
43
Power Save – On
Set to enable Power Save operation for battery powered Loudmouth. This
option will have no effect unless Battery Operation – On is set.
44
Power Save – Off
√
Set to disable Power Save operation for RPS-1A powered Loudmouth.
Summary of Contents for JBS-446D
Page 2: ......
