background image

COnTrOl Panel OPeraTIOns

7

temperature settInG

The actual temperature of the pool water is constantly 

displayed  on  the  screen  The  temperature  will  show 

once the pump has been operating for 1 minute.
Press the tempº + or tempº − button once to display 

the set temperature. Each time  or − button is 

pressed  again,  the  set  temperature  will  increase  or 

decrease. After 3 seconds the screen will automatically 

return  to  display  the  actual  water  temperature.  If 

the  water  is  cooler  than  the  set  temperature  the 

thermostatically  controlled  heater  will  automatically 

turn on to heat the spa water. The temperature setting 

can be adjusted from between 26°C - 40°C. 

mode settInG

The mode button is used to switch between Standard, 

Economy and Sleep modes. 
Press  mode  to  enter  mode  programming.  Press 
tempº − to cycle through to the desired mode (the 

mode will flash on the screen until confirmed), then 

press mode to confirm selection.
standard mode maintains the desired temperature. 

Note that the current water temperature is displayed 

only when the pump has been operating for at least 

1 minute. The 

Std

  icon will display until the mode is 

changed.
economy mode heats the spa to the set 

temperature only during filtration cycles. The 

Ecn

 

icon will display until mode is changed. 
Pressing VSP while in Economy mode puts the spa 

in 

Standard-In-Economy

 mode, which operates 

the same as Standard mode for 1 hour, then 

automatically reverts back to Economy mode. Both 

the 

Std

  

and 

Ecn

  

icons display in this mode. During 

this time you can press the mode button to revert 

back to Economy mode immediately.
sleep mode heats the water to 11° C only during 

filter cycles. The 

SLP

 

icon will display until mode is 

changed.

InItIal start-up 

priming mode

When your Riptide pool is first connected it will go into 

Priming  mode  (after  displaying  some  configuration 

information). The screen will display 

Pr.

The  Priming  mode  will  last  for  up  to  4  minutes  and 

then the spa will begin to heat and maintain the water 

temperature in the Standard mode. You can exit Priming 

mode early by pressing tempº + or tempº -.

settInG tHe tIme

To  set  the  time  press  the  time  button  and  then  the 
mode button and the digital display window will display 

a digital clock with the HOUR setting flashing. Use the 
tempº + or tempº −

 

buttons to change to the correct 

hour (each press changes the time by 1 hour). When 

the HOUR is correct, press the mode button to save 

changes and the MINUTES setting will flash. Use the 
tempº + or tempº −

 

buttons to change to the correct 

minutes (each press changes the time by 1 minute). 

Press the mode button to save changes and complete 

the time setting. 

Note:

1.  The  time  displayed  is  set  as  a  12-hour  clock 

(AM/PM).  To  change  to  a  24-hour  clock  see 

User 

Preferences

 on page 9.

2. If you don’t touch the Tempº + or Tempº 

− 

buttons, 

after 3 seconds the display will exit the time setting.

ICon leGend

Heat Icon - indicates different 
temperature level.
variable speed drive Icon - when 
the Variable Speed Drive is switched 
on the jet icon will show on the screen.
light Icon - when the lights in the spa 
are on the light icon will show.

Summary of Contents for Manta SuperPro























Reviews: