background image

 

Warning 

  Do  not  dismantle,  repair  or  modify

product except authorized professional

-  This  could  damage  product  safety.  When  you

think  product  is  in  trouble,  refer  to  user’s

manual or contact our service center

.           

  Do not touch product during the use of

product or sometime after using it. 

-Gill  part  and  top  plate  of  product  is  very  hot.

You could get burned 

General 

prohibition 

No Touch 

  Keep product out of children’ reach. 

-Do  not  allow  children  get  closer,  they  could  get

burned. 

  Do not touch product during the use of

product or sometime after using it. 

-Gill  part  and  top  plate  of  product  is  very  hot.

You could get burned 

Must do 

General 

prohibition 

  Consult  with  gas  supplier  or  installer  for  gas

connection and product installation. 

-We  are  irresponsible  for  any  accidents  caused  by

wrong gas connection or

 product installation

  Be  careful  not  to  get  burned,  right  aft er

operation or during operation. 

-Kettle  is  very  hot  and  filled  with  a  high  temperature  of  steam
during  operation  or  right  after  operation.  You  could  get  burned
on your hands or face etc. 
 
-Do not touch kettle when you open the lid. Keep away your face
from the product as much as you can and hold “kettle lid knob”
then open the lid slowly by letting inside stem outside. 

Must

 do 

Must do 

Summary of Contents for RSK-500


















Reviews: