Rinnai FM10LA Operation & Installation Manual Download Page 4

Rinnai 

HW_GI_FM10 OIM

WARNING

BEFORE USING THIS APPLIANCE

Before proceeding with the operation or installation read this manual thoroughly and gain a full 

understanding of the appliance, to ensure safe and correct use.
Always comply with the following precautions to avoid dangerous situations and to ensure 

optimum performance.
Failure to carefully read and follow all instructions in this manual can result in equipment 

malfunction, property damage, personal injury and/or death.

DANGER:

  Indicates an imminently hazardous situation which, if not avoided, will result in 

personal injury or death.

WARNINGS:

  Indicates a potentially hazardous situation which, if not avoided, could result in 

personal injury or death.

CAUTIONS:

  Indicates a potentially hazardous situation which, if not avoided, could result in 

minor or moderate injury or damage to the appliance. It may also be used to alert against unsafe 

practices.

WARNING

REGULATORY INFORMATION

Your Rinnai gas instantaneous  water heater

 

has been certified by the Australian Gas Association.

 

The A.G.A. Certification Number is shown on the data plate.

This appliance must be installed correctly by an appropriately licensed tradesperson. 
The installation of gas and water must conform to local regulations, including local OH&S 

requirements. The installation must also comply with the instructions supplied by Rinnai.
Please keep this instruction booklet in a safe place for future reference.

All dimensions referred to in these instructions are in millimetres, unless otherwise specified.

Notice to Victorian Consumers

This appliance must be installed by a person licensed with the Victorian Building Authority. Only 

a licensed person will have insurance protecting their workmanship. So make sure you use a 

licensed person to install this appliance and ask for your Compliance Certificate.

For further information contact the Victorian Building Authority on 1300 815 127.

WARNING

WARNING ABOUT HOT WATER

Hot water can cause scalding. Those most 

at risk are children and disabled, elderly 

and infirm persons. 

Rinnai have water heater models which 

limit the delivery temperature to 50°C which 

significantly  reduces  the  scald  hazard. 

Temperature limiting devices may also be 

able to be fitted. Contact Rinnai for further 

information.

ALWAYS

 test the water temperature before 

use, such as when filling a bath or basin or 

entering a shower, to ensure it is suitable 

for the application and will not cause scald 

injury.

ALWAYS

 supervise children whenever 

they are in the bathroom or near other 

sources of hot water. Ensure any hot water 

taps are closed firmly after use.

WARNINGS & IMPORTANT INFORMATION

Summary of Contents for FM10LA

























Reviews: