background image

 

Fan Convector Manual 

15 

Operating The Heater 

TURNING ON:                                                                              

Press the 

ON/OFF 

button to operate the heater. The 

ON indicator will glow green. After approximately 3 
seconds the spark generator will be heard before the 
burner ignites and the ON indicator glows red,                 
indicating that the burner is lit. Warm air can be felt 
coming from the  louvers approximately 5 seconds 
later. 

 

 

NOTE 

If the heater does not ignite on initial try, air may be 

remaining in the gas supply line. The spark generator 

will only continue for 15 seconds. After this, it will be 

necessary to press the ON/OFF button OFF, then ON 

again. 

TURNING OFF:                                                               

Simply press the 

ON/OFF 

button to switch off the 

heater. The ON indicator will go out. The convection 
fan will continue to operate for several minutes after 
the burner has gone out in order to cool the                            
appliance. 

Do not unplug the appliance while the 

convection fan is running.

 

NOTE 

DO NOT 

turn heater off by unplugging. The                           

convection fan will continue to run as the appliance 

needs to cool. 

Room Temperature Adjustment:

 

NOTE                                                                                                              

The room temperature and pre-set temperatures can 

only be displayed and adjusted when the heater is 

running.

 

Press the " 

" button to increase the temperature 

setting or 

"  

" button to decrease the temper-

ature setting. 

The temperatures can be set to: 

a) [L] low (minimum combustion) 

b) [60°F] to [80°F] in 2°F increments 

c) [H] high (maximum combustion) 

(Default temperature setting is 72°F) 

NOTE                                                                                                              

If the heater does not ignite, then the pre-set                             

temperature may not be set to a setting that is          

higher than the actual room temperature.

 

AUTO OFF: 

When 

AUTO OFF 

is selected, the indicator light will 

glow. The unit will now be under full thermostat                        
control. The heater will operate to reach the                
selected room temperature and then turn 

OFF. 

Press 

AUTO OFF again to disable this function. 

NOTE   

                                                                                        

When 

AUTO OFF 

indicator light is not glowing , the 

unit will continue to produce heat in at least a low fire                         

capacity until the unit is manually powered down. 

 

Summary of Contents for FC510













































Reviews: