background image

Rinnai 

DD FP Solar Pre Heat System OIM

SAFETY AND REGULATORY INFORMATION

WARNING

DO NOT

 operate this system before reading the manufacturers instructions.

This appliance must be installed, commissioned and serviced by an authorised person in 

accordance with all applicable local rules and regulations.
Access covers of water heating system components will expose 240V wiring and 

MUST

 be 

removed by an authorised person.
This appliance is not intended for use by persons (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge, unless they have been 

given supervision or instruction in use of the appliance by a person responsible for their safety.
For continued safety of this appliance it must be installed, operated and maintained in accordance 

with the manufacturer’s instructions.
Children should be supervised to ensure they 

DO NOT

 play with the appliance.

Any power leads from the water heater system components 

MUST BE

 plugged into an external 

weatherproof electrical outlet. If the power supply cord of any water heating components is 

damaged, it 

MUST BE

 replaced by an authorised person in order to avoid a hazard, using genuine 

replacement parts available from Rinnai. Take care not to touch power plugs with wet hands.
Care should be taken not to touch the pipe work as it may be 

HOT!

 The pipes between the 

solar collectors and storage cylinder 

MUST BE

 copper or alternative material pipes that may be 

supplied by Rinnai. Plastic pipe is 

NOT

 suited to the water temperatures and pressures that may 

occur in the system. 

DO NOT

 place articles on or against this appliance.

DO NOT

 store chemicals or flammable materials near this appliance.

DO NOT

 operate with collectors or covers removed from this appliance.

DO NOT

 activate pump unless cylinder is full of water.

NEVER

 use a flammable spray such as hair spray, lacquer, paint, etc near this unit as this may 

cause a fire.

 

WARNING

NOTICE TO VICTORIAN CONSUMERS

This appliance must be installed by a person licensed with the Victorian Building Authority.
Only a licensed person will have insurance protecting their workmanship.
So make sure you use a licensed person to install this appliance and ask for your Compliance 

Certificate. For Further information contact the Victorian Building Authority on 1300 815 127.

WARNINGS AND IMPORTANT INFORMATION

Summary of Contents for Enduro SP200B

































Reviews: