Rinnai ASPIRATION RHFE-750ETR Installation Manual Download Page 22

Rinnai Australia

20

ASP Flue Installation Manual

CONNECTING HEATER EXHAUST & AIR SUPPLY

CONNECTING HEATER EXHAUST

  

1.

 Lubricate the O-Ring of the exhaust connection and fit the telescopic exhaust pipe of the heater.

 Push the telescopic tube fully home so that the end of the exhaust connection and the collar of the

telescopic exhaust pipe are fully mated.     

2. Attach the flue locking clamp provided with the heater over the telescopic exhaust pipe and the exhaust

connection of the flue transition. Ensure that the teeth of the flue locking clamp engage both 

 

A

 the collar of

the telescopic exhaust pipe and 

 

B

 the collar of the exhaust connection of the flue transition.   

3.

 Close the clamp to secure both components together.

4. Adjustable the telescopic exhaust pipe to attain the desired position of the heater, 

 DO NOT extend  beyond

the indicator groove.       

5.

 Fix the telescopic exhaust in place with the exhaust lock. 

 The clamp of the exhaust lock is attached to

the telescopic exhaust pipe whilst the finger tabs are secured around the collar of the fixed part of the exhaust.

CONNECTING COMBUSTION AIR HOSE 

This section describes how to connect the exhaust pipe from the
Aspiration heater to the exhaust connection on  flue transition
ASPDFK or ASPKIT03.

 This joint MUST BE properly secured in accordance

with these instructions using the clips provided.

If this joint is not secured properly, products of
combustion could disperse into the room being heated
which may result in a dangerous condition.

The combustion air hose of the heater is attached to the
large diameter combustion air inlet.

  Secure the combustion air hose to the

combustion air inlet with cable tie supplied with
the heater.

The air hose MUST BE properly secured in
accordance with these instructions for safe and
reliable operation of this heater.

The rubber cap (when supplied) is designed to fit
both the left and right hand combustion air inlet
and MUST cover the air inlet not in use.

Exaust Connection

ASPDFK

ASPKIT03

CAUTION

1

2

3

!

Telescopic Exhaust pipe

Exhaust connection

!

!

!

!

!

4

5

!

!

Maximum

limit of telescopic

extension

INCORRECT

over extension

of telescopic

extension

Collar

Collar

!

!

!

!

!

CAUTION

Summary of Contents for ASPIRATION RHFE-750ETR

























Reviews: